Sharp PN-Y556 - Page 40

40
E
SETUP menu
Function Command Direction Parameter Reply Control/Response contents *
DATE/TIME SETTING DATE WR
AABBCCDDEE AABBCCDDEE AA: Year, BB: Month, CC: Day, DD: Hour, EE: Minute
○
LAN SETUP DHCP client DHCP WR 0-1 0-1 0: OFF, 1: ON
IP Adress IPAD WR
XXXXXXXXXXXX XXXXXXXXXXXX X: Only number is ok. If the number is less than three digits, to three digits to ll zero.
Example: 192168150001
Subnet mask SBMK WR XXXXXXXXXXXX XXXXXXXXXXXX X: Only number is ok. If the number is less than three digits, to three digits to ll zero.
Example: 255255255000
Default gateway DFGW WR XXXXXXXXXXXX XXXXXXXXXXXX X: Only number is ok. If the number is less than three digits, to three digits to ll zero.
Example: 000000000000
DNS1 DNS1 WR XXXXXXXXXXXX XXXXXXXXXXXX X: Only number is ok. If the number is less than three digits, to three digits to ll zero.
Example: 000000000000
DNS2 DNS2 WR XXXXXXXXXXXX XXXXXXXXXXXX X: Only number is ok. If the number is less than three digits, to three digits to ll zero.
Example: 000000000000
FTP ON/OFF
SELECT
FCHE WR 0-1 0-1 0: FTP connection OFF, 1:FTP connection ON
MONITOR NAME MNTR WR
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
X: Sixteen characters or less; half-width alphanumeric characters, “-”, and “_”.
(The eld cannot be left blank, and spaces cannot be entered.)
FTP Username FUSR WR XXXXXXXX XXXXXXXX X: Eight characters or less; half-width alphanumeric characters, “-”, and “_”.
(The eld cannot be left blank, and spaces cannot be entered.)
FTP Password FPAS WR XXXXXXXX XXXXXXXX X: Eight characters or less; half-width alphanumeric characters, “-”, and “_”.
(The eld cannot be left blank, and spaces cannot be entered.)
Telnet
USERNAME
USER WR XXXXXXXX XXXXXXXX X: Eight characters or less; half-width alphanumeric characters, “-”, and “_”.
(The eld can be left blank, but spaces cannot be entered.)
Telnet
PASSWORD
PASS WR XXXXXXXX XXXXXXXX X: Eight characters or less; half-width alphanumeric characters, “-”, and “_”.
(The eld can be left blank, but spaces cannot be entered.)
ID SETTING ID NO.SETTING IDST W
0-25
Sets the monitor’s ID number. (“0” means “no ID number”.)
R
0-25
Returns the monitor’s ID number.
ID NO. SETTING
(ONCE)
IDSL W
1-25
Sets a monitor ID number.
This ID number is only effective for the command immediately after this
command.
0
Clears the ID number if one has been designated.
ID NO. SETTING
(SUBSEQUENT)
IDLK W
1-25
Sets a monitor ID number.
This ID number is effective for the next and all subsequent commands after this
command.
0
Clears the ID number if one has been designated.
-
MULTI ENLARGE ENLG WR 0-1 0-1 0: OFF, 1: ON
ENLARGE MODE EMHV WR 11-55 11-55 1 x 1 (OFF) to 5 x 5 (“m x n” is expressed as “mn”, where m and n are the
numbers of monitors specied for the longest direction and the shortest direction
respectively.)
IMAGE POSITION
(M x N)
EPHV WR 11-55 11-55 Species values in the order of IMAGE POSITION IN LONGEST/ SHORTEST
DIRECTION.
BEZEL ADJUST BZCO WR 0-1 0-1 0: OFF, 1: ON
ENLARGE/
IMAGE POSITION
SETTING
ESHV WR XXYY XXYY XX: ENLARGE MODE (Same as EMHV), YY: IMAGE POSITION (Same as
EPHV)
THERMAL SENSOR SETTING STDR WR 0-3 0-3 0: LANDSCAPE, 1: PORTRAIT, 2: FACE UP, 3: FACE DOWN
○
ADJUSTMENT
LOCK
MONITOR
BUTTONS
ALCM WR 0-1, 3 0-1, 3 0: UNLOCKED, 1: LOCK ALL, 3: LOCK EXCEPT POWER
REMOTE
CONTROL
ALCR WR 0-3 0-3 0: UNLOCKED, 1: LOCK ALL, 2: LOCK EXCEPT VOLUME,
3: LOCK EXCEPT POWER
Autoplay ATPL WR 0-1 0-1 0: PHOTO, 1: MOVIE
ALL RESET RSET W 1
-
Controlling the Monitor with a computer (RS-232C)