6
FLASHING LIGHT
To activate the light functions, you must switch AUDIO-2 to AUX mode.
1. Long press the LIGHT button to turn on/o the decoration LED
lighting around the speakers.
2. Press the LIGHT button repeatedly to choose the lighting mode for
the inner lights:
L-1: Blue LED will be on constantly.
L-2: Red LED will be on constantly.
L-3: Green LED will be on constantly.
L-4: Three-colors ash in gradual mode.
L-5: Seven-colors ash in gradual mode.
L-6: Three-colors dance with the music.
Press one more time to turn o .
BLUETOOTH OPERATION
1. Rotate the AUDIO-1 knob to BT mode to enter Bluetooth mode, “ - bt -
” will be lit up and ash on the display screen.
2. Turn on the Bluetooth function on your device, scan “SHARP PS-940”
and connect. Input the password 0000 if required.
3. Once successfully connected, there will be a prompt sound and “ - bt - ”
will stop ashing.
4. Adjust the EQ e ect by sliding the EQ SLIDER-A.
5. Rotate the A-VOLUME knob or adjust the volume on the external
device to increase or decrease the music volume to your desired level.
6. Control the playback with your audio device.
7. Press the BLUETOOTH CONNECTION button to disconnect the
bluetooth connection.
Wireless connection with multiple PS-940 (connect to the compatible
speakers).
1. Select a PS-940 as the host speaker. Long press the BLUETOOTH
CONNECTION button, “
bt - “ will be shown on the display screen.
2. Continuously press the BLUETOOTH CONNECTION button twice on
another one or more PS-940. When “ - bt
” shown on the display,
it means the speakers have been connected to the host speaker
successfully.
3. Make your device connect to the host speaker. Then you can enjoy the
music via your the speakers.
NOTES: The product supports 3 phones (except for Iphone) to establish
bluetooth connection at the same time.
USB OPERATION
This unit provides two USB ports, one for playback, and another for
charging.
1. Set AUDIO-1 to USB mode. “ - USb -” will be shown on the display.
2. Plug the USB memory stick to the USB PLAYBACK PORT on the unit.
Playback will start automatically from track 01.
3. To pause the playback, press the PLAY/PAUSE button on the top panel
of the unit. Press this button again to resume the playback.
4. To select a desired track, press the PREVIOUS or NEXT button
respectively during playing until the desired track appears on the
display. The unit will start to play automatically.
AUX-IN OPERATION
1. Set the AUDIO-1 to AUX mode, “AUX” will be shown on the display.
2. Connect your audio device to the AUX IN JACK on the top panel of the
unit with an AUX IN cable.
3. Rotate the A-VOLUME knob to adjust the music volume.
4. Use the EQ SLIDER-A to adjust your favor sound e ect.
5. Control the playback with your audio device.
MIC/GUITAR OPERATION
1. Set the AUDIO-2 to MIC/GUITAR mode.
2. Connect your microphone/guitar to the MIC or GUITAR JACK.
3. Rotate the B-VOLUME knob to adjust the microphone/guitar volume.
4. Use the EQ SLIDER-B to adjust your favor sound e ect.
NOTES: The EQ SLIDER-B cannot work if the AUDIO-2 is set to AUX mode.
Technical speci cation
Model PS-940
Power Supply AC ~ 100-240V, 50/60Hz
Rated Power Consumption 20W
Standby Power Consumption <0.5W
Output Power 2 x 25 W (RMS)
Total max power output 180 W
Frequency Response 40Hz-15KHz
Battery
Built-in 37,44Wh Li-ion battery
battery pack with 4x 2.600 mAh
Bluetooth
Version V 4.0
Maximum power transmitted <20 dbm
Frequency bands 2402 MHz ~ 2480 MHz
NOTE: Speci cations are subject to change for continuous improvement
without prior notice.
635mm
224mm 300mm
8,0 kg
To Next Page
Loading...
Need help?
General
Weight and Dimensions
