Sharp RT-1157H - Specifications

jut+*
SPECIFICATIONS
Type:
4-track
2-channel
stereo
cassette
tape
recorder/player
deck
with
built-in
Dolby
noise
reduction
system
Power source: AC110/220/240V, 50/60Hz
Power consumption: 13W
Semiconductors: 4-IC
23-Transistor
15-Diode
3-LED
Dimensions:
Width:
408
mm
{16-1/16")
Height:
168mm
(6-1/4’’)
Depth:
252mm
(9-15/16"}
Weight: 6 kg (13.2 Ibs}
Microphone jacks, 6.8K ohms
Line input jacks, 5OK ohms
Record/playback socket, 6.8K
ohms
Headphones jack, 8 ohm
Line output jacks, 50K ohms
Record/playback socket, 50K
Input circuitry:
Output circuitry:
ohms
Tape:
Philips
standard
campact
cassette
-
tape
Tape speed: 4.8 cm/sec. (1-7/8 ips.}
Recording system: AC bias system (85 kHz)
Erasing system: AC erasing
Fast forward & rewind time:
100 seconds (C-60)
0.2% (DIN 45507)
0.09% WRMS
Wow and flutter:
LAYOUT OF FRONT AND REAR
1. Cassette chamber lid opener button
(JKNBPOO76AFSC) (RT-1157H)
{JKNBPOO76AFSB) (RT-1157HB)
2, Cassette chamber (GDORF3053AFSA)
3. Digital tape counter (KCOUBO072AFZZ)
4. Tape counter reset button (KCOUBO072AFZZ)
5. Record indicator, D603 (VHPGL-52AR/1F)
6. Dolby N.R. indicator, D602 (VHPGL-52AR/1F}
7. APSS indicator cover (HDECQOO56AFSA) (RT-1157H)
' (HDECQOODS6AFSB) (RT-1157HB)
8.
Level
meters,
ME101
&
ME201
(RMTRLO1G0AFZZ)
9. Peak level indicator, D601 (VHPGL-52AR/1F)
10. Power switch knob (JKNBM1004SESF) (RT-1157H)
(JKNBM1004SESG} (RT-1157HB}
11, Pause key (JKNBRO170AFSE} (RT-1157H}
(JKNBRO110AFSA) (RT-1157HB)
12. Record key (JKNBRO11OAFSF) (RT-1157H}
{JKNBRG110AFSB} (RT-1157HB}
13. Rewind/Reverse APSS key
{JKNBRO110AFSE} (RT-1157H)
(JKNBROTIOAFSA) (RT-1157HB}
14. Play key (JKNBRO11OAFSE) (RT-1157H}
(JKNBRO1IOAFSA) (RT-1157HB)
15. Fast-forward/Forward APSS key
(JKNBROTIOAFSE) (RT-1157H}
(JKNBROTIOAFSA) (RT-1157HB}
Frequency
response:
Normal
tape;
40
—
12,500
Hz
SHARP
,
(DIN
45
511)
(c-60UD
)
40
—
12,500
Hz
+
3dB
MAXELL
C-60UDXL
II
tape;
40
—
14,000
Hz
(DIN
45
511)
40
—
14,000
Hz
+
3dB
52
dB,
For
normal
tape,
at
LINE-
IN,
without
Dolby
N.R.
system
10
dB
(at
over
5
kHz)
Signal to noise ratio:
Dolby N.R. effect:
Distortion: 1.5%
Channel separation: 35 dB
Erase ratio: 65 dB
Input sensitivity and input impedance:
Microphone: 0.2 mV, 6.8K ohms .
Record/playback socket:
0.2 mV, 6.8K ohms
Line in: 63 mV, 50K ohms
Output level and loaded impedance:
Headphones:
63
mV
{"0"
VU),
8 ohms
Record/playback socket:
500 mV ("0" VU},
5OK ohms
500 mV ("0 VU),
5OK ohms
Specifications
are
subject
to
change
without
prior
notice.
Line out:
PARTS (Refer to Figure 3-1 and Figure 3—2)
16,
Stop
key
(JKNBRO110AFSE)
{RT-1157H)
(JKNBRO110AFSA)
{RT-1157HB)
17.
Headphones
jack,
J4
{QUAKJOOSSAFZZ)}
18.
Microphone
jacks,
Ji
&
J2
(QUAKZO062AFZZ)
19.
input
selector
switch
knob
(JKNBM1004SESF)
{RT-1157H)
(JKNBM1004SESG)
(RT-1157HB)
Pa
20.
Dolby
N.R.
switch
knob
(UKNBM1004SESF)
(RT-1157H}
(JKNBM1004SESG)
(RT-1157HB)
21.
Bias
selector
switch
knob
(JKNBM1004SESF)
(RT-1157H)
(JKNBM1004SESG)
(RT-1157HB}
22.
Equalizer
selector
switch
knob
(JKNBM1004SESF)
(RT-1157H)
(JKNBM1004SESG)
(RT-1157HB)
23.
Record
level
contro!
knobs
(JKNBKOIG9AFSA
&
JKNBNO366AFSA)
(RT-1157H}
(JKNBKOI69AFSB
&
JKNBNO366AFSB)
(RT-1157HB)
24.
Input
jacks,
JZA
&
J3B
(QSOCZ2463AFZZ)
25,
Record/playback
socket
{5-pin,
DIN},
J3E
(QSOCZ2463AFZZ)
26.
Output
jacks,
J8C
&
J3D
(QSOCZ2463AF
ZZ}
27.
Mains
voltage
selector,
SO501
(QSOCE0410AGZZ}
28.
Mains
supply
cord
a
o>