How to troubleshoot no power on my Sherwood NewCastle R-772?
If your Sherwood Receiver has no power, it could be due to a disconnected AC input cord. Ensure the cord is securely connected. Also, check the AC wall outlet by testing it with a lamp or another appliance to rule out a faulty outlet or if the outlet is off.
Why is there no sound coming from my Sherwood NewCastle R-772?
If there is no sound coming from your Sherwood Receiver, check the following: * Ensure the speaker wires are properly connected. * Adjust the master volume to an audible level. * Make sure the MUTE button is not activated. * Verify that you've selected the correct input source. * Confirm all connections between components are correct. * Ensure the HDMI AUDIO OUT is set to OFF. * Check that all audio settings are configured correctly.
What to do if the Sherwood NewCastle R-772 remote control is not working?
If the remote control for your Sherwood Receiver isn't working, try replacing the batteries first. If that doesn't solve the issue, check to see if anything is obstructing the remote sensor on the receiver and remove it.
How to troubleshoot no picture on Sherwood NewCastle R-772 Receiver?
If you're not getting a picture on your Sherwood Receiver, ensure that the video connections between the unit and the monitor TV are correctly made. Also, verify that you've selected the correct input source on your monitor TV.
Why is the FM reception so poor on my Sherwood Receiver?
If you're experiencing poor FM reception on your Sherwood Receiver, first ensure that an antenna is connected. If one is connected, try repositioning it for better reception.
Why can't my Sherwood NewCastle R-772 receive any stations?
If your Sherwood Receiver is unable to receive stations, ensure that an antenna is connected. Also, make sure you are tuning in to the desired station frequency and try moving the antenna to a different position and retry tuning.
Why is there no picture with an HDMI connection on my Sherwood NewCastle R-772 Receiver?
If you are not getting a picture with an HDMI connection on your Sherwood Receiver, ensure that the HDMI connection between the unit and the monitor TV is correctly made. Also, confirm that the monitor TV or other equipment supports HDCP; the unit will not output a video signal if HDCP is not supported.
Why are the surround speakers not working on my Sherwood NewCastle R-772?
If there's no sound from the surround speakers on your Sherwood Receiver, check that a surround mode is selected and that the master volume and surround level are appropriately adjusted. Ensure you are using a stereo or surround source and that the surround speaker setting is not set to "NO".
Why is there no sound from the center speaker on my Sherwood NewCastle R-772?
If you're not hearing sound from the center speaker of your Sherwood Receiver, check if Dolby Virtual Speaker or stereo mode is selected; if so, select a surround mode. Also, verify that the center speaker setting is not set to "NO", and adjust the master volume and center level.
Why are the surround back speakers silent on my Sherwood NewCastle R-772 Receiver?
If there is no sound from the surround back speakers on your Sherwood Receiver, it could be due to several reasons. Check if the input signal format or current surround mode supports 7.1 (or 6.1) surround. Ensure the surround back channels' power amplifier is assigned to surround back and not "BI-AMP" or "ROOM 2". Also, verify that the master volume and surround back level are not too low, and confirm that the surround back speaker setting is not set to "NO".
General| Channels | 7.1 |
|---|---|
| Total Harmonic Distortion | 0.08% |
| Input Sensitivity | 200 mV (line) |
| Signal-to-Noise Ratio | 100 dB |
| HDMI Inputs | 4 |
| AM/FM Tuner | Yes |
| Power Output | 100 watts per channel (8 ohms) |
| Frequency Response | 10 Hz - 100 kHz |
| Video Connections | Composite, Component, HDMI |
| Tuning range | FM: 87.5-107.9 MHz, AM: 530-1710 kHz |
| Speaker load impedance | 4-16 ohms |
| Dimensions | 440 x 165 x 430mm |
Details on equipment testing and compliance with FCC regulations for digital devices.
Instructions for connecting FM and AM antennas for optimal signal reception.
Guide to connecting various video sources like DVD players, VCRs, and TVs.
Steps for connecting audio sources like tape decks and MD recorders.
Guidance on connecting optical and coaxial digital audio sources.
Detailed instructions for connecting various speaker configurations, including bi-amping.
Instructions for connecting RF remote antennas and multi-room system kits.
Identification and function of all buttons and jacks on the receiver's front panel.
Explanation of the various indicators and information shown on the receiver's display.
Steps to set up and operate other audio/video components using the universal remote.
Guide to entering setup codes, searching codes, and programming macro functions.
How to use the dedicated remote for ROOM 2 source playback.
Steps for powering on the receiver and selecting audio/video input sources.
Detailed description of all available DTS and Dolby Digital surround sound modes.
Instructions for tuning into AM/FM radio stations, including auto and manual tuning.
Guide to subscribing and listening to XM Satellite Radio.
Details on sleep timer, display brightness, and audio information display.
Procedures for recording analog and digital audio/video signals.
How to access and navigate through the receiver's on-screen display menus.
Configuration settings for amplifier assignment, subwoofer mode, and HDMI audio.
Guide to automatic and manual speaker setup, distance, crossover, and room equalization.
Adjusting individual channel levels, sound modes, and equalization parameters.
Setting up ROOM 2 playback and configuring input source assignments.
List of setup codes for programming the remote to control various TV, VCR, and DVD brands.
To Next Page