What to do if SHOWTEC SHARK SPOT ONE fixture doesn't turn on?
If your SHOWTEC DJ Equipment fixture isn't powering on, first ensure that the power switch is on and all cables are securely plugged in. If the issue persists, the primary fuse might have blown, requiring a replacement.
Why is my SHOWTEC DJ Equipment responding erratically to the controller?
If your SHOWTEC DJ Equipment fixture resets correctly but responds erratically or not at all to the controller, ensure the controller is properly connected. Also, verify that the 3-pin XLR Out of the controller matches the XLR Out of the first fixture. If the signal is reversed, install a phase reversing cable between the controller and the first fixture.
How to troubleshoot no light on SHOWTEC SHARK SPOT ONE DJ Equipment?
If your SHOWTEC DJ Equipment fixture has no light, start by checking if the unit is properly plugged into an appropriate power supply. If the issue persists, the fuse might be blown and needs replacement. For fuse replacement, refer to page 23. If the LEDs are the cause, return the Shark to your Showtec dealer. If none of these steps resolve the issue, it's best to refer servicing to a technician.
What to do if some SHOWTEC SHARK SPOT ONE respond erratically?
If your SHOWTEC DJ Equipment fixture resets correctly, but some respond erratically or not at all to the controller, it could be due to poor data quality. Inspect connections and cables, repairing or replacing damaged ones. Ensure the data link is terminated with a 120 Ohm termination plug in the output jack of the last fixture. Verify the fixture addressing and bypass one fixture at a time to identify any defective units disturbing the link. If the 3-pin XLR Outs don't match, install a phase-reversing cable or swap pins 2 and 3 in the erratic fixture.
How to fix SHOWTEC SHARK SPOT ONE DJ Equipment no response to DMX?
If you're experiencing no response to DMX with your SHOWTEC DJ Equipment, verify the DMX settings and ensure the DMX addresses are correct. Check the DMX cable by unplugging the unit, changing the cable, and reconnecting to electrical power. To determine if the controller or light effect is at fault, test the controller with other DMX products. If the controller doesn't operate properly, have it repaired. If it does, take the DMX cable and the light effect to a qualified technician.
Why does SHOWTEC SHARK SPOT ONE light cut out intermittently?
If your SHOWTEC DJ Equipment's light or LEDs cut out intermittently, the fixture might be overheating. Allow the fixture to cool, clean the fan, and ensure the air vents are not blocked. You can also turn up the air conditioning. If the LEDs are damaged, disconnect the fixture and return it to your dealer. Also, ensure the power supply settings match your local AC voltage and frequency, disconnecting the fixture while checking and correcting if necessary.
Why does SHOWTEC DJ Equipment shutter close suddenly?
If the shutter on your SHOWTEC DJ Equipment closes suddenly, it may be due to the color wheel, gobo wheel, or a gobo losing its index position, causing the fixture to reset the effect. If the problem persists, contact a technician for servicing.
Instructions for safely unpacking and checking the product upon arrival.
Information on LED degradation factors and lifespan improvement.
Essential safety guidelines for installation and operation.
Technical specifications and features of the Showtec Shark Spot One.
General visual overview of the lighting fixture.
Illustration and identification of components on the front of the device.
Illustration and identification of components on the back of the device.
Overview of available operation modes: Auto, Sound, Master/Slave, DMX.
Instructions for operating a single fixture in stand-alone modes.
Guide to setting up multiple fixtures in a master/slave configuration.
Steps for connecting and controlling fixtures via DMX.
Information on connecting multiple fixtures and data cable types.
Description of the device's control panel and buttons.
Diagram and explanation of the device's menu structure.
Procedure for setting the DMX starting address for fixtures.
How to select between 8-channel and 14-channel DMX modes.
Options for setting the fixture's operation mode (DMX, Auto, Sound, Slave).
How to choose and run built-in programs.
Adjusting settings like Pan/Tilt Reverse, Sensitivity, DMX Fail.
Steps for calibrating fixture parameters like Pan, Tilt, Gobo.
Viewing current software version, mode, and DMX address.
Detailed mapping of DMX channels for 8-channel mode.
Detailed mapping of DMX channels for 14-channel mode.
Instructions on how to replace a blown fuse in the device.
Steps to diagnose and resolve issues where the light does not operate.
Steps to diagnose and resolve DMX communication problems.
General| Type | Moving Head |
|---|---|
| Light Source | LED |
| Pan Range | 540° |
| Tilt Range | 270° |
| Power Supply | 100-240V AC, 50/60Hz |
| Gobo Wheel | 7 gobos + open |
| Control | DMX512, Master/Slave, Auto |
| Color Wheel | 8 colors + open |
To Next Page