12
Childproof lock
The oven has a childproof lock to prevent children from
switching it on by accident.
The oven will not respond to any settings.You can still set the
clock and the timer when the childproof lock is activated.
If the type of heating and temperature or grill setting are set, the
childproof lock interrupts the heater element.
Note: If a hob is connected, it will not be affected by the
childproof lock on the oven.
Activating the childproof lock
No cooking time or end time should be set.
Press and hold the
h button for approx. four seconds.
The
@ symbol appears in the display. The childproof lock is
activated.
Deactivating the childproof lock
Press and hold the
h button for approx. four seconds.
The
@ symbol goes out in the display. The childproof lock is
deactivated.
Changing the basic settings
Your oven has various basic settings. These settings can be
customised to suit your requirements.
No other time-setting option should have been set.
1. Press and hold the 0 button for approx. 4 seconds.
The current basic setting for the clock display is shown in the
display, e.g. c1 1 for selection 1.
2. Use the @ or A button to change the basic setting.
3. Confirm by pressing the 0 button.
The next basic setting appears in the display. You can scroll
through all levels with the
0 button and change the setting
with the
@ or A button.
4. To finish, press and hold the 0 button for approx. 4 seconds.
All basic settings are applied.
You may change the basic settings at any time.
Care and cleaning
With good care and cleaning, your oven will remain clean and
fully-functioning for a long time to come. Here we will explain
how to maintain and clean your oven correctly.
Notes
■ Slight differences in the colours on the front of the oven are
caused by the use of different materials, such as glass,
plastic and metal.
■ Shadows on the door panel which look like streaks, are
caused by reflections made by the oven light.
■ Enamel is baked on at very high temperatures. This can
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
Cleaning agents
To ensure that the different surfaces are not damaged by using
the wrong type of cleaning agent, observe the information in the
table. Do not use
■ harsh or abrasive cleaning agents,
■ cleaning agents with a high concentration of alcohol,
■ hard scouring pads or sponges,
■ high-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Basic setting Selection 1 Selection 2 Selection 3
c1 Clock display always* only with
the
0 but-
ton
-
c2 Signal duration
upon completion of
a cooking time or
timer period
approx.
10 seconds
approx.
2 minutes*
approx.
5 minutes
c3 Waiting time until a
setting is applied
approx.
2 seconds
approx.
5 seconds*
approx.
10 seconds
* Factory setting
Area Cleaning agents
Control panel Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Do not use glass cleaners or glass
scrapers.
Stainless steel Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Remove traces of limescale, grease,
starch and albumin (e.g. egg white) immedi-
ately. Corrosion can form under such resi-
dues.
Special stainless steel cleaning products
suitable for hot surfaces are available from
our after-sales service or from specialist
retailers. Apply a very thin layer of the
cleaning product with a soft cloth.
Door panels Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Cooking com-
partment
Hot soapy water or a vinegar solution:
Clean with a dish cloth.
If there are heavy deposits of dirt, use a
stainless steel scouring pad or oven
cleaner. Only use when the cooking com-
partment is cold.
Glass cover for
the oven light
Hot soapy water:
Clean with a dish cloth.
Seal
Do not remove.
Hot soapy water:
Clean with a dish cloth. Do not scour.
To Next Page
Loading...
Need help?
General