Siemens Sinumerik 840 sl - Page 137

Examples
4.2 Protection zones
Basic logic functions: Axis monitoring, protection zones (A3)
Function Manual, 11/2006, 6FC5397-0BP10-2BA0
71
$SN_PA_CONT_ABS[0,2] 110 ; Endpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 2
$SN_PA_CONT_ABS[0,3] 0 ; Endpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 3
$SN_PA_CONT_ABS[0,4] 0 ; Endpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 4
$SN_PA_CONT_ABS[0,5] 0 ; Endpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 5
$SN_PA_CONT_ABS[0,6] 0 ; Endpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 6
$SN_PA_CONT_ABS[0,7] 0 ; Endpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 7
$SN_PA_CONT_ABS[0,8] 0 ; Endpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 8
$SN_PA_CONT_ABS[0,9] 0 ; Endpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 9
$SN_PA_CENT_ORD[0,0] 0 ; Midpoint of contour[i], ordinate value
; Protection zone for spindle chuck, contour element 0
$SN_PA_CENT_ORD[0.1] 0 ; Midpoint of contour[i], ordinate value
; Protection zone for spindle chuck, contour element 1
$SN_PA_CENT_ORD[0,2] 0 ; Midpoint of contour[i], ordinate value
; Protection zone for spindle chuck, contour element 2
$SN_PA_CENT_ORD[0,3] 0 ; Midpoint of contour[i], ordinate value
; Protection zone for spindle chuck, contour element 3
$SN_PA_CENT_ORD[0,4] 0 ; Midpoint of contour[i], ordinate value
; Protection zone for spindle chuck, contour element 4
$SN_PA_CENT_ORD[0,5] 0 ; Midpoint of contour[i], ordinate value
; Protection zone for spindle chuck, contour element 5
$SN_PA_CENT_ORD[0,6] 0 ; Midpoint of contour[i], ordinate value
; Protection zone for spindle chuck, contour element 6
$SN_PA_CENT_ORD[0,7] 0 ; Midpoint of contour[i], ordinate value
; Protection zone for spindle chuck, contour element 7
$SN_PA_CENT_ORD[0,8] 0 ; Midpoint of contour[i], ordinate value
; Protection zone for spindle chuck, contour element 8
$SN_PA_CENT_ORD[0,9] 0 ; Midpoint of contour[i], ordinate value
; Protection zone for spindle chuck, contour element 9
$SN_PA_CENT_ABS[0,0] 0 ; Midpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 0
$SN_PA_CENT_ABS[0.1] 0 ; Midpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 1
$SN_PA_CENT_ABS[0,2] 0 ; Midpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 2
$SN_PA_CENT_ABS[0,3] 0 ; Midpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 3
$SN_PA_CENT_ABS[0,4] 0 ; Midpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 4
$SN_PA_CENT_ABS[0,5] 0 ; Midpoint of contour[i], abscissa value
; Protection zone for spindle chuck, contour element 5