Home
Siemens
Protection Device
SIPROTEC 7UT612
Siemens SIPROTEC 7UT612 User Manual
5
of 1
of 1 rating
94 pages
Give review
Manual
Specs
To Previous Page
To Previous Page
Loading...
Subject to technical alteration
Copying of this document and giving it to others and the u
se
or communication of the contents thereof, are forbidden with-
out express authority. Offenders ar
e liable to the payment of
damages. All rights are reserved in the event of the grant of
a patent or the registration of a utility mo
del or design.
Order-no.
: C53000-L18
40-B001-03
Siemens Aktiengesellschaft
93
Table of Contents
Default Chapter
3
Preface
3
Revision Index
7
Table of Contents
9
1 PROFIBUS Communication Modules
11
Communication Module Types and Hardware Revisions
12
Communication Module Types
12
Hardware Revisions
12
Compatibility of the Communication Module Hardware with PROFIBUS-DP Firmware Versions and Mapping Files
13
Display of Module-Specific Information at the SIPROTEC Device
15
Block 1: Status and Parameters of the PROFIBUS-DP Slave
17
Block 2: Firmware Versions and Mapping File
19
Block 3: Module Hardware Information and Boot Firmware Version
20
Block 4: OLM Information
21
Block 5: Status of the Event List Via PROFIBUS-DP
24
2 Parameters and Properties
25
Bus Specific Parameters
26
PROFIBUS-DP Settings
26
Configuration of the Fibre-Optical Interface
28
Event List Settings
31
PROFIBUS-DP Configuration Data
31
Execution of Switching Operations Via PROFIBUS-DP
32
Command Output Modes
32
Transformer Tap Change Commands
33
Behaviour under Special Operating Conditions
33
Response in the Event of Disturbed Communication to the PROFIBUS-DP Master
34
Communication Interruption
34
Signalling of Line-Breaks in a Redundant Fibre-Optical Ring
35
Annunciations to the PROFIBUS-DP Master
37
Event List Via PROFIBUS-DP (Sequence of Events Recorder)
38
Properties of the Event List
39
Structure of a PROFIBUS-DP Telegram with Event List
40
Telegram in Input Direction
40
Telegram in Output Direction
42
Handshake Mechanism
43
3 Data Type Definitions
45
Single-Point Indication (SP, Input)
46
Single Command (SC, Output)
47
Double-Point Indication (DP, Input) / Double Command (DC, Output)
48
Measured Value (Signed Integer)
49
Measured Value (Float)
50
Metered Measurand (Unsigned Long)
51
Transformer Tap Change Command (TC)
52
Transformer Tap Position Indication (TM)
53
Message Block for Event List Via PROFIBUS-DP
54
4 PROFIBUS-DP - Parameterization in DIGSI
57
Interface Selection and Mapping Files
58
Standard Mappings 3-1 to 3-N
58
Compatibility with Standard Mappings of Previous Versions
59
Interface Selection and Mapping Selection in DIGSI 4.21
59
Interface Selection and Mapping Selection in DIGSI 4.3 or Higher
63
Customization of the Allocations
66
Scaling of Measured Values
70
Measurement Conversion
70
Number Representation Depending on the Parameterization
71
Parameterization in DIGSI
73
Time Synchronization
75
PROFIBUS-DP Master
75
Parameterization in DIGSI
77
Using SFC14 and SFC15 in STEP7
79
5 Technical Data
83
Connection Via the PSE Module
84
Connection Via the PSO Module
86
Glossary
89
Index
91
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Siemens SIPROTEC 7UT612 and is the answer not in the manual?
Ask a question
Siemens SIPROTEC 7UT612 Specifications
General
Brand
Siemens
Model
SIPROTEC 7UT612
Category
Protection Device
Language
English
Related product manuals
Siemens SIPROTEC 7UT613 series
638 pages
Siemens SIPROTEC 7UT63 series
638 pages
SIPROTEC 7UT633*-* N series
638 pages
SIPROTEC 7UT635*-* N series
638 pages
Siemens SIPROTEC 4 7UT6 Series
684 pages
Siemens SIPROTEC 7UM62
638 pages
Siemens SIPROTEC 7UM61
94 pages
Siemens SIPROTEC 5 7UM85
92 pages
Siemens SIPROTEC 7VE61
94 pages
Siemens SIPROTEC 7SD80
416 pages
Siemens SIPROTEC 7SJ531
362 pages
Siemens siprotec 7SA522
606 pages
To Previous PageTo Previous Page
Loading...
Need help?
General
