Siemens SSD

Siemens Siemens
Siemens Siemens
Siemens
IndustryIndustry
IndustryIndustry
Industry
,,
,,
,
Inc. Inc.
Inc. Inc.
Inc.
Building Building
Building Building
Building
TT
TT
T
ecec
ecec
ec
hnologies Dihnologies Di
hnologies Dihnologies Di
hnologies Di
visionvision
visionvision
vision
P/N 315-034170-13
System Status Display
Installation Instructions
Models SSD / SSD-INTL
INTRODUCTION The Model SSD/SSD-INTL from
Siemens Industry, Inc., is an optional
FireFinder module that displays the
event status of a system remotely
from the PMI/PMI-2/PMI-3 (XLS),
FCM2041-U2 (Desigo Fire Safety
Modular), FCM2041-U3 (Cerberus PRO Modular). It has four 40 character alphanu-
meric LCD character lines, backlit upon status change or display toggling. This module
is supervised by the main panel and also has LEDs and an optional sounder to indicate
the status of the system. The SSD/SSD-INTL has the capability to store up to 1500
event messages and has pushbuttons to scroll through these events. Its display is
independent from the display on the PMI/PMI-2/PMI-3 (XLS), FCM2041-U2 (Desigo
Fire Safety Modular), FCM2041-U3 (Cerberus PRO Modular).
The following items are supplied with the SSD/SSD-INTL:
• SSD mounting plate (P/N 300-034289) with the SSD-TB interface board
(P/N 515-034170)
• 8-pin wiring interface cable (P/N 555-134347)
• SSD housing (P/N 195-134170) with an SSD-main board (P/N 557-034170)
• Overlay—The SSD has one overlay, the SSD-INTL has three overlays.
- SSD overlay (P/N 200-134290 in English)
- SSD-INTL overlays (P/N 200-134754 in French, P/N 200-134755 in
Spanish, P/N 200-134756 in Portuguese)
• 4 screws to mount the housing to the mounting bracket (P/N 545-634442)
The SSD-INTL is used in applications where French, Spanish or Portuguese is the
primary language. It is identical to the SSD in all other ways, and will be referred to in
the remainder of this document as SSD.
OPERATION The SSD has six LEDs and a sounder to indicate the status of the fire alarm panel.
The LCD indicates the state of a specific event. The SSD also has push buttons that
allow the user to scroll through the events list, control the sounder and acknowledge
events displayed on the LCD.
The SSD must be configured in the Zeus Programming Tool as Display only. Refer to
the Programming section on page 5 for information on configuring the system.
Controls and Indicators The front panel of the SSD contains 6 LEDs, 1 LCD display, up and down navigational
buttons and a Local Acknowledge button as shown in Figure 1.
Figure 1
SSD System Status Display
AUDIBLES
SILENCED
ON
SUPERVISORY
ALARM
LOCAL
ACK
TROUBLE
SECURITY

Siemens SSD Specifications

General

Brand	Siemens
Model	SSD
Category	Monitor
Language	English

Summary

Introduction to the SSDSSD-INTL System Status Display

System Operation and Configuration

Controls and Indicators Overview

Alarm LED Status

Indicates alarm status: OFF (no alarm), ON (flashing) for unacknowledged, ON (steady) for acknowledged.

Supervisory LED Status

Indicates supervisory status: OFF (no event), ON (flashing) for unacknowledged, ON (steady) for acknowledged.

Security LED Status

Indicates security status: OFF (no event), ON (flashing) for unacknowledged, ON (steady) for acknowledged.

Trouble LED Status

Indicates trouble status: OFF (no event), ON (flashing) for unacknowledged, ON (steady) for acknowledged.

Audible NAC Status LEDs

Indicates NACs status: ON (steady) for activated or silenced NACs, OFF for supervisory mode.

Sounder Operation

Indicates system sounder status: OFF (supervisory/acknowledged), ON (steady) for unacknowledged alarm.

Pushbutton Functions

Local Acknowledge Button

Activates LCD backlight or turns off the sounder for displayed events.

Up Arrow Button

Activates LCD backlight or displays the event with the next higher priority.

Down Arrow Button

Activates LCD backlight or displays the event with the next lower priority.

LCD Display Modes

Supervisory Mode LCD

Displays current date, time, custom messages, and system ID.

Active Event Mode LCD

Displays event status, address, date/time, custom message, category, and event counts.

Pre-Installation Switch Settings

S1 DIP Switch Configuration

Configures the SSD for network wiring termination (S1-SW1) and other unused settings.

Network Addressing and Reset

Network Address Switches (S2, S3, S4)

Set the three-digit HNET network address for the SSD, matching the Zeus Programming Tool.

Reset Switch (S11)

Momentarily closing this switch re-initializes the SSD operation.

Programming the SSD Module

Required Programming Settings

Configure HNET Address and Base Language Custom Message via Zeus Programming Tool.

SSD Display and Event Filtering Options

Configure display type, sounder, and filtering for alarms, security, supervisory, and trouble events.

Wiring Connections

Typical SSD Connection Diagram

Illustrates wiring from SSD to FireFinder-XLS/Desigo Fire Safety Modular/Cerberus PRO Modular.

Wiring Diagram Details

Shows connections to NIC-C and PSC-12, including wire size and termination notes.

SSD Installation Procedure

Mounting the SSD

Mounts directly onto a user-supplied double gang or 4-inch switchbox.

Connecting the SSD Assembly

Connects 8-pin cable from mounting plate to SSD assembly and secures with screws.

Applying the Overlay

Peel, align, and press overlay onto SSD assembly for display protection.

Electrical Ratings and Power

Input Voltage and Current

Specifies typical input voltage (24VDC) and current (200mA max).

Power Supply Requirements

Auxiliary power supply must be UL approved for Fire Protection Signaling.

Cyber Security Disclaimer