SIMCom Wireless Solutions SIM8262E-M2

To Next Page

SIM8262E-M2 5G HAT

Features

• Based on Qualcomm platform, support 5G NSA and SA networking, support multi-mode and

multi-band

• Integrated multi-constellation system dual-frequency positioning: GPS, GLONASS, BeiDou,

Galileo and QZSS

• Support Windows / Linux / Android and other operating systems

• USB 3.1 port (USB 2.0 compatible) for connecting to PC, Raspberry Pi, or Jetson Nano host

board to enable high speed 5G communication

• Onboard M.2 B KEY slot, compatible with 5G modules such as SIM8202X-M2 / SIM8200EA-M2 /

SIM8262X-M2 series

• Onboard UART, PWR, and RST control pin, built-in voltage level translator, enabled via DIP

switch, for use with hosts like Raspberry Pi or Arduino

• Onboard USB-C connector, enabled via switch, for connecting standalone power supply for

the module, allows more loads, stable and flexible power supply

• Onboard power switch, reset button, and LED indicator, easy to switch the control module

on and off and check the running status

• Onboard 4-way SMA to IPEX antenna adapting interface, factory default welded SMA

terminals, antenna installation is more convenient

• Onboard two SIM card slots, dual-card single-standby, can be switched and enabled by AT

command

• Onboard audio interface and audio decoding chip, which can be used for voice manipulation

such as making calls

• High-efficiency power supply circuit, up to 3A output current

5G Module Parameters

SIM8200EA-M2

SIM8202G-M2

SIM8262E-M2

SIM8262A-M2

5G Standard

3GPP R15

3GPP R16

Need help?

Do you have a question about the SIMCom Wireless Solutions SIM8262E-M2 and is the answer not in the manual?

Summary

SIM8262 E-M2 5 G HAT Features

5 G Module Parameters Overview

Hardware Pinout Definition

Working With Windows

Windows Direct Driver Installation

Step-by-step guide for installing drivers and software on Windows.

Windows Manual NDIS Dial-up Internet Setup

Configure NDIS dial-up connection for internet access on Windows.

GPS Positioning Guide

Working With Raspberry Pi

Raspberry Pi Initial Configuration

Setting up the Raspberry Pi with the correct system image and driver.

Raspberry Pi 5 G Networking Setup

Configuring the 5G module for network connectivity on Raspberry Pi.

Raspberry Pi Live Streaming Setup

Using the camera and FFmpeg for live streaming from Raspberry Pi.

Introduction to OpenWrt

Prepare OpenWrt System Image

Download and burn the OpenWrt system image to an SD card.

OpenWrt Login and Initial Settings

Accessing the web interface and initial configuration of OpenWrt.

Configure OpenWrt Networking

Setting up network interfaces and firewall rules in OpenWrt.

Test OpenWrt 5 G Connectivity

Verifying network port identification and testing 5G speed.

Working With Jetson Nano

Jetson Nano Initial Configuration

Setting up the Jetson Nano with the correct system image and driver.

Jetson Nano 5 G Network Setup

Configuring the 5G module for network connectivity on Jetson Nano.

Product Resources and Documentation

Software Tools and Drivers

List of essential software, drivers, and utilities for the module.

Datasheets and Application Notes

Links to detailed technical documentation and usage guides.

Troubleshooting Common Issues

Optimize 5 G Network Speed

Diagnosing and improving slow 5G network speeds.

Resolve SIM Card and Registration Issues

Resolving SIM card recognition and network registration problems.

Fix Connectivity and Driver Problems

Troubleshooting NDIS dial failures and driver installation issues.

Diagnose GPS and Antenna Problems

Diagnosing problems with GPS signal reception and antenna connections.

Manage VOLTE Functionality

Enabling or disabling the VOLTE feature for voice calls.