SIMPA HZB62GN - User Manual

Questions and Answers

A
Amanda GardnerAug 3, 2025
What to do if the SIMPA HZB62GN Hob flame goes off when using?
- D
  dicksonamyAug 3, 2025
  If the SIMPA Hob flame goes off while you're using it, there could be several reasons. It could be due to a dirty or wet ignition electrode, in which case you should wait a minute before restarting the ignition. The wind may have blown out a small flame, activating the flame failure safety device; if this happens, turn the rotary knob to the off position, wait a minute, and then restart the ignition. The 4-hour automatic flame-off safety device might have activated, requiring you to turn the rotary knob to the off position and restart the ignition if you need to continue cooking. Lastly, the overheat protection device could be activated, so turn the rotary knob to the off position, wait a minute, and then restart the ignition.
J
James RichardsAug 7, 2025
Why is there no flame on my SIMPA Hob?
- J
  Jerry RamirezAug 7, 2025
  If your SIMPA Hob isn't producing a flame, several factors could be at play. First, check if the gas meter valve or the appliance gas supply valve is turned off; if so, open them completely. It's also possible that air is trapped inside the gas pipe, in which case you should repeat the ignition process until the air is removed. Another potential issue is that the burner might be blocked by an aluminum disc, which you would need to remove. Finally, the ignition electrode could be dirty or wet, requiring you to clean and dry it.
N
nhughesAug 11, 2025
How to fix no ignition spark on SIMPA HZB62GN Hob?
- R
  richardcarterAug 11, 2025
  If there is no ignition spark on your SIMPA Hob, it could be due to several reasons. The batteries might be consumed, so try replacing them. Alternatively, the batteries might be wrongly placed, so ensure they are correctly positioned. It's also possible that the ignition electrode is dirty or wet; if so, clean and dry it.
A
Audrey GloverAug 16, 2025
What to do if the flame does not persist on my SIMPA HZB62GN Hob?
- J
  James KellerAug 16, 2025
  If the flame on your SIMPA Hob does not persist, ensure that the control knob is fully pressed. Turn the gas control knob anti-clockwise to the maximum position. Also, make sure that the rotary knob is fully pressed and turned to the ignition position.
B
Brian WhiteAug 20, 2025
Why does my SIMPA Hob have a yellow flame?
- S
  Steven MackAug 20, 2025
  A yellow flame on your SIMPA Hob usually indicates that the burner cap and burner body have dirt. To resolve this, wash the burner cap and burner body in warm water with detergent. After washing, dry them thoroughly and replace them in the correct position before restarting the ignition.
M
Michael AndersonAug 25, 2025
Why is my SIMPA Hob making abnormal noise when using it?
- M
  Maria RodriguezAug 26, 2025
  Abnormal noise when using your SIMPA Hob can be caused by incorrect placement of the burner cap and burner body. Ensure that the appliance cools down, then replace the burner cap and burner body correctly before restarting the ignition.
K
Kristina SalinasAug 28, 2025
Why is the flame unstable on my SIMPA Hob?
- A
  andrew92Aug 28, 2025
  An unstable flame on your SIMPA Hob can occur due to deformation or incorrect placement of the burner cap and burner body. If the burner cap and burner body are deformed, contact Towngas Company to replace the parts. If the burner cap and burner body are incorrectly placed, replace them correctly after the appliance cools down and restart the ignition.