Setting: date, current time, summer / winter time, work / rest days
4
4.1 4.2
7 s.
4.3 4.4 4.5 4.6 4.84.7
4.1. Press the validation key (●) for over 7 seconds. SET and YEAR appear
on the screen.
4.2 / 4.3 / 4.4. Setting current time: 4.2: Year, 4.3: Month, 4.4: Day.
4.5 / 4.6. Adjusting current time: 4.5: Time, 4.6: Minutes.
4.7. Enter the geographic area to set the automatic winter / summer time
change: EU = Europe, US = USA, OFF = other countries (in this case,
the time will not change automatically from summer time to winter time.
Follow the procedure from 4.1 to 4.6 if you need to change the time).
4.8. Setting work / rest days:
- To save one one daily program, to be repeated every day of the week,
select (circle) all the days of the week. (default setting)
- To save two different programs, (work / rest days); select (circle) only the
work days, the others will be rest days by default.
You can save and exit setting mode by pressing the validation key for 3
seconds (●).
5.2. Changing the time of an up or down order
1. Using the selection keys (◄,►) you can select the order of commands to
be saved (
1 ou
2) - Not necessary for daily program.
2. Press the key for the command to be saved (▲ or ▼) for 8 seconds. The
shutters will carry out the command and it is saved.
1. Using the selection keys (◄,►) select the command
(
1 or
2) to be changed.
2. Press the validation key (●) for 3 seconds. SET and
EDIT appear on the screen, EDIT flashes.
3. Press the validation key (●) for 1 second.
4. Set the time for the program to be carried out and
press for 1 second on the validation key (●)
5. Set the minutes for the program to be carried out and
press the validation button (●)
- After 5 seconds, the current time will replace the previous
program time by ashing. Press for 3 more seconds.
- If the key is released before 8 seconds, changes will not be
saved.
Changes made in this chapter will be applied to all days of the week in the daily program and all circled days in work / rest
days mode.
5.1. Memory function: Quick save an order with a long press
: display only if work / rest days set
: display only if work / rest days set
1 2
8 s.
8 s.
1 s.1 s.
5431
3 s. 1 s.
2
Changing programs
5
Can be accessed from Automatic mode
Resetting programs
6
Changing the batteries
7
6.1. Press the validation key (●) for 7 seconds, SET and YEAR appear on the screen and the
year ashes.
6.2. Press the PROG button for 8 seconds.
The transmitter will then be in manual mode and be pre-programmed this way:
- Winter / summer time change: European time zone
- Daily program: Up at 7.30 am / down at 20.00 pm.
- The current date and time will remain unchanged.
PROG 8 s.
1 2
7 s.
2 X
LR03 AAA 1.5V
120 s.
MAX.
2/2
SIMU hereby declares that the radio equipment covered by these instructions is in compliance with the requirements of Radio Directive
2014/53/EU and the other essential requirements of the applicable European Directives. The full text of the EU declaration of conformity is
available at www.simu.com.
We care about our environment. Do not dispose of your appliance with the usual household waste. Take to
an accredited collection point for recycling.
Please separate storage cells and batteries from other types of waste and recycle them via your local
collection facility.
Read the chapter entitled Safety instructions.
Risk of explosion if the battery is replaced by an incorrect type.
Replace the batteries when the low battery indicator (d) goes on.
To Next Page
Loading...
Need help?
General
