Need help?Do you have a question about the Skyrc B6AC neo and is the answer not in the manual?
General| Discharge Power | 5W |
|---|---|
| Charge Current | 0.1-6.0A |
| Discharge Current | 0.1-1.0A |
| Balance Current | 300mA/Cell |
| Battery Types Supported | LiPo, Li-ion, LiFe, NiMH, NiCd, Pb |
| Cell Count for LiPo/Li-ion/LiFe | 1-6S |
| Cell Count for NiMH/NiCd | 1-15 cells |
| Pb Voltage | 2-20V |
| Operating Temperature | 0-40°C |
| Storage Temperature | -20-60°C |
| Balance Port | JST-XH |
| Input Voltage | 100-240V AC |
| Cooling System | Fan |
Use the '+' button to navigate menus or increase parameter values.
Use the confirm button to enter settings, confirm choices, and stop progress.
Use the '-' button to navigate menus or decrease parameter values.
Connects the charger to either AC or DC power sources for operation.
Connects the battery to the charger, following specific safety precautions.
Details on connecting LiPo batteries using a balance adapter for safe charging.
Initiates the process to configure charge settings for lithium batteries.
Allows selection of the specific lithium battery chemistry (LiPo, Lilo, LiFe, LiHV).
Choose the correct number of battery cells for the selected lithium battery type.
Choose the desired working mode (Balance CHG, Charge, Storage, Discharge).
Set the terminal charging voltage for the lithium battery.
Set the desired charge or discharge current value for the operation.
Initiates the selected charging or discharging program.
Steps back to the main interface from the current setting screen.
Stops the current charging or discharging program.
Choose NiMH or NiCd as the battery type for programming.
Select the correct number of cells for NiMH/NiCd batteries.
Choose the desired working mode for NiMH/NiCd batteries.
Set the delta voltage for NiMH/NiCd battery charging.
Set the charge or discharge current for NiMH/NiCd batteries.
Initiates the NiMH/NiCd charging or discharging program.
Steps back to the previous setting screen for NiMH/NiCd.
Stops the current NiMH/NiCd charging or discharging program.
Choose 'PB' for programming Lead-Acid batteries.
Select the correct number of cells for Lead-Acid batteries (3S/6S).
Choose the working mode for Lead-Acid batteries (Normal, AGM, Cold Charge, Discharge).
Set the terminal voltage for Lead-Acid battery charging.
Set the charge or discharge current for Lead-Acid batteries.
Initiates the Lead-Acid battery charging or discharging program.
Steps back to the previous setting screen for Lead-Acid batteries.
Stops the current Lead-Acid battery charging or discharging program.
Adjust output voltage and current for the DC Power function.
Select Start to activate DC Power mode and connect equipment.
Explains how CC/CV mode adapts to various applications and load needs.
Details how CC mode prevents overcurrent situations for device safety.
Highlights CC/CV mode's suitability for precise lithium-ion battery charging.
Explains optimization for loads needing specific voltage or current.
Describes how dynamic mode switching improves operational efficiency.
Explains safe LED driving using CC mode and CV mode for parallel strings.
Navigate through System Setting to reach the Battery Meter function.
Use the meter to measure battery voltage and resistance.
Select the desired battery type (LiPo, Lilon, LiFe, LiHV, NiMH, NiCd, PB).
Select battery cells based on type (e.g., 1-6S for Li-xx).
Select the work mode (Balance CHG, Charge, Storage, Discharge).
Set the cut-off voltage for the charging process.
Set the charge or discharge current value.
Initiates the charging program.
Navigates back to the main interface.
Customize a period for program protection.
Customize the maximum charging capacity.
Enable or disable trickle charging for compatible batteries.
Enable holding voltage for automatic charging at low voltage.
Choose the desired language for the user interface.
Set the minimum voltage for input protection.
Adjust the brightness of the screen.
Adjust or turn off key and beep sounds.
Choose how to be reminded upon program completion.
Enable or disable the start-up warning message.
Set the output voltage for DC Power (2.0-27.0V).
Set the output current for DC Power (1.0-10.0A).
Enable DC power output and return to the main interface.
Measure battery voltage and internal resistance.
Restore the charger to its default factory settings.
Check the current system status of the charger.
Upgrade the charger's firmware.
Check the certification information.
Navigates back to the previous interface.
Details SkyRC's disclaimer of liability for improper product use.
To Next Page
