Sloan EAF-275 Series User Manual

The information contained in this document is subject to change without notice.
6
5
9
11
12A/12B
7B
7A
8
2
4
3A
3B
3C
3D
13
1A/1B
13
14
10
SOLIS
®
EAF-275
Repair Parts and Maintenance Guide
190
Faucets and Soap Dispensers
PARTS LIST—EAF-275 FAUCET
Item
No. Code No. Part No. Description
1A. 0335013 EAF-14-A Faucet Sensor Assembly without i.q.-cliq
1B. 0335014 EAF-16-A Faucet Sensor Assembly with i.q.-cliq
2. 3335021 EAF-1006 Cap and Solar Cell Assembly
3A. 0335012 EAF-15 0.5 gpm (1.9 Lpm) VR Aerator Spray Head –
Pre 03/2011
3B. 0335008 EAF-10 2.2 gpm (8.3 Lpm) Aerator Spray Head
3C. 0335011 EAF-13 2.2 gpm (8.3 Lpm) Laminar Flow Spray Head
3D. 0335029 EAF-51 0.35 gpm (1.3 Lpm) Multi-Laminar Spray Head
4. 3335018 EAF-1003-A Battery Replacement Kit (CR-P2)
5. 0335000 EAF-1 Faucet Mounting Kit
6. 0335007 EAF-9 Strainer (Filter)
7A. 3335019 EAF-1004 Mixer Handle Assembly and Cartridge
7B. 3335020 EAF-1005 Handle Repair Kit
8. 3335022 EAF-1007 Handle Cap
9. 3335023 EAF-1008 13” (330 mm) Flexible Supply Hose
10. 0335001 EAF-2 Solenoid
11. 3365468 ETF-312-A Trim Plate for 4” Center-set Sink
12A. 3365024 ETF-510-A Trim Plate for 8” Center-set Sink
12B. 3362022 SFP-22-A Use when needing 8” for EAF-35-A extension
13. 3335035 EAF-35-A Faucet Extension Kit
14. 3335046 EAF-40-A 2-1/4” Faucet Extension Kit. Raises faucet such
that outlet height complies with California Ofce of
Statewide Health Planning and Deveplopment
EAF-275 Series Faucet date code 1101 and
newer. Product revised to make spray head
vandal resistant without need for special spray.
EAF-15 only works on product date code 1052
and older.

Sloan EAF-275 Series Specifications

General

Product Type	Electronic Faucet
Valve	Solenoid Valve
Flow Rate	0.5 gpm
Power Supply	Battery or Hardwired
Sensor Range	Adjustable
Finish	Chrome
Compliance	ADA Compliant
Activation	Infrared Sensor
Flush Volume	0.5 gpm
Rough-In	Not Applicable

Summary

Backup Battery Replacement

Step 1: Close Supply Stops

Close water supply stops before proceeding with battery replacement.

Step 2: Remove Cap Assembly

Loosen retaining screw with hex wrench and remove battery compartment cap.

Step 3: Replace Battery

Remove old battery, dispose properly, and prepare for new battery insertion.

Step 4: Wait Period

Observe a three (3) minute waiting period before inserting the new battery.

Step 5: Insert New Battery

Insert new 6 Volt CR-P2 lithium battery and reinstall the battery cover.

Step 6: Open Supply Stops

Open the water supply stops to restore faucet operation after battery replacement.

Troubleshooting Guide

Faucet Inoperative

Troubleshoot faucet not functioning due to sensor obstruction or 'Permanent Off' mode.

Uncontrolled Water Flow

Address faucet issues causing uncontrolled water delivery or abnormal operation.

No Water (Solenoid Clicks)

Resolve no water delivery when solenoid clicks by checking supply stops and strainers.

No Water (No Solenoid Click)

Troubleshoot no water delivery without solenoid click, indicating a low battery condition.

Reduced Water Flow

Diagnose slow flow or dribble by checking supply stops, strainers, and aerator clogs.

Continuous Water Flow

Address faucet not stopping delivery or dripping after use, possibly due to solenoid failure.

Flashing LED Indicator

Identify flashing LED indicator as a symptom of a low battery power level.

Temperature Adjustment

Troubleshoot water temperature by adjusting supply stops or the integral mixing valve.