These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,”
“Warning” or
“Danger
.” They are all important notes for safety and must be followed in addition to International
Standards (ISO/IEC), Japan Industrial Standards (JIS)
Note 1)
and other safety regulations
Note 2)
.
Note 1) ISO 4414: Pneumatic fluid power – General rules relating to systems.
ISO 4413: Hydraulic fluid power – General rules relating to systems.
IEC 60204-1: Safety of machinery – Electrical equipment of machines. (Part 1: General requirements)
ISO 10218-1992: Manipulating industrial robots -Safety.
JIS B 8370: General rules for pneumatic equipment.
JIS B 8361: General rules for hydraulic equipment.
JIS B 9960-1: Safety of machinery – Electrical equipment of machines. (Part 1: General requirements)
JIS B 8433-1993: Manipulating industrial robots - Safety.
etc.
Note 2) Labor Safety and Sanitation Law, etc.
1. The compatibility of the product is the responsibility of the person who designs the equipment
or decides its specifications.
Since the product specified here are used under various operating conditions, their compatibility with the specific equipment
must be based on specifications based or after analysis and or test results. The expected performance and safety assurance of
the equipment will be the responsibility of the person who has determined its compatibility with the product. This person should
also continuously review all specifications of the product referring to its latest catalog information, with a view to giving due
consideration to any possibility of equipment failure when configuring the equipment.
2. Only trained personnel should operate machinery and equipment.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or
equipment including our products must be performed by an operator who is appropriately trained and experienced.
3.
Do not service or attempt to remove components and machinery/equipment until safety is confirmed.
1. Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control
positions.
2. When the product is to be removed, confirm that the safety process as mentioned above are implemented and the power from
any appropriate source is cut, and read/understand the specific product precautions carefully.
3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC if the product is to be used in any of the following conditions.
1. Conditions and environments beyond of the given specifications, or if product is used outdoors.
2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military,
medical treatment, combustion and recreation, food and beverages, emergency stop circuits, press applications, safety
equipment or other applications unsuitable for the standard specifications described in the product catalogue.
3. An application which could have negative effects on people, property, or animals and therefore requires special safety
analysis.
4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical pro tective
function, and periodical checks to confirm proper operation.
Warning
Caution:
Operator error could result in injury or equipment damage.
Danger :
In extreme conditions, there is a possibility of serious injury or loss of life.
Warning
:
Operator error could result in serious injury or loss of life.
Safety Instructions
Limited Warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited Warranty and Disclaimer” and “Compliance
Requirements”. Read and accept them before using the product.
The product is provided for use in manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract
if necessary. If anything is unclear, contact your nearest sales branch.
Caution
Limited Warranty and Disclaimer
1. The warranty period of the product is 1 year in service or 1.5 years after it is delivered.
Note)
The product may also have specified durability, running distance or replacement parts. Please
consult your nearest sales point.
2. For any failure or damage reported within the warranty period which is clearly SMC's responsibi-
lity, replacement product/parts will be provided.
This limited warranty applies only to SMC's product independently, and not to any other damage
incurred due to the failure of it.
Note) Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after is deliver.
Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the
deterioration of rubber material are not covered by the limited warranty.
Compliance Requirements
When the product is exported, strictly follow the laws required by the Ministry of Economy, Trade
and Industry (Foreign Exchange and Foreign Trade Control Law).
Safety Instructions
To Next Page
Loading...
Need help?
General
