Snapper SERIES 19 - Page 17

DRIVE SYSTEM SELF-PROPELLED
Footnotes:
TP 400-5187-B-WB-N
Manual No. 700614921" STEEL DECK WALK BEHIND MOWERS
SERIES 19
17
Part No Descri
p
tionItem Qt
y
Note
1 7012354 1 BELT, Poly-V
2 7034179 1 LINK, Differential (Comm.)
-- 7051921 ASSEMBLY, Clutch Idler (Includes items 3 thru 7)
3 7032832 1 ARM, Clutch Idler
4 7012124 1 PULLEY, Idler, V21
5 7091025 1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap, GR 5
6 7090303 1 NUT, 1/4-28 Hex Top Lock
7 7012117 4 BUSHING, 3/8” I.D. Nylon
8 7072284 1 SHAFT, Hex Drive
9 7024521 1 PULLEY, Poly-V (2” O.D.) for non-Commercial models
10 7090188 1 WASHER, 11/32” Flat
11 7012126 1 SPRING, Idler- Torsion
12 7012111 1 STUD, Idler (3/8-24 thread)
13 7031873 1 HOLDER, Bearing (Inner Half)
14 7028014 1 BALL BEARING, Spherical O.D., .38 I.D.
15 7011025 1 O-RING, V21
16 7090289 1 NUT, 3/8-24 Hex Center Lock, GR 5
17 7031809 1 HOLDER, Bearing (Outer Half)
18 7091294 1 WASHER, .28 x .63 x .06 Flat
19 7091629 1 COTTER PIN, .06 x .50 YZ or 7090673
20 7046784 1 BELT, Engine Drive (Stretch)
21 7300977A 1 THRUST PLATE, Short was 7034281
22 7010746 2 RETAINING RING, .625 External
23 7026693 1 BALL BEARING- 3/4” Bore
24 7012125 1 GUIDE, Thrust Plate (3/8-24 thread)
25 7091542 1 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx)
26 7015753 1 BALL JOINT, 1/4-28 (not shown) see Handles & Controls page
(item 39)
27 7090095 2 NUT, 1/4-28 Hex (not shown) see Handles & Controls page
(item 40)
28 7074145 1 LINK, Transfer (1/4-28 thread)
29 7090391 1 WASHER, 5/16” Internal Tooth Lock
30 7090390 3 WASHER, 3/8” Internal Tooth Lock
31 7090122 1 WASHER, 3/8” Flat
32 7091630 3 NUT, 3/8-24 Hex
33 7012122 1 SPRING, Clutch - 21S
34 7090585 2 NUT, 5/16-18 Hex Flange Lock, GR 5 or 7091601
35 7090731 1 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR 5
36 7090539 2 SCREW, 1/4-20 x 1/2” Hex Flange Self-Tap or 7091122
NOTE: * Includes Steel Drive Disc Assy (7073528), Bushing (7013893), 3/8-16 Hex Nut (7091302) & item 38.