Snapper SPA521 - Page 5

LOOP HANDLE & CONTROL ASSEMBLIES
Footnotes:
TP 400-5023-4-CW-N
Manual No. 7006928PRO HYDRO
SERIES 1 & 2
5
Part No Descri
p
tionItem Qt
y
Note
1 7011138 1 IGNITION KEY, Pair
2 7012685 1 NUT, 5/8-32 Hex (Ignition Switch)
3 7012686 1 NUT, 1/2-27 Hex (Special)
4 7014341 2 RETAINING RING Truarc #5133-50
5 7017817 1 SWITCH, Ignition, 2-Pole, Recoil Start (except Kohler 23HP)
5 7027698 1 SWITCH, Ignition used on Kohler 23HP
6 7022166 1 ROD, Pivot, 1/2” Dia. x 18.542 w/2 retaining Ring Grooves
7 7027141 2 SWIVEL
8 7027225 1 SWITCH, OPC, Single Pole (NC) used on Loop Handle except
Kohler 23HP
8 7023355 1 SWITCH, OPC, (NO/NC) used on Kohler 18HP
9 7028856 2 CONTROL ROD (Traction)
10 7028857 4 BEARING, Nyliner
11 7074648 1 ROD, Operator Presence Control
12 7029139 1 SPRING, OPC- Loop Handle
13 7029715 1 SWITCH, Toggle
14 7034827 1 PANEL, Left
15 7034828 1 PANEL, Right
16 7041748 1 BAIL, Operator Presence Control (Weldment)
17 7091303 4 BOLT, 5/16-18 x 1” Short Neck Carriage, GR 5
18 7090977 2 NUT, 1/4-20 Hex Jam
19 7091222 2 BOLT, 1/4-20 x 1-3/4” Hex Head Cap, GR 5
20 7091030 2 BUSHING, 1/2” Machine
21 7091122 8 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
22 7091297 2 NUT, 5/16-24 Hex, GR 5
23 7091299 4 NUT, 3/8-16 Hex Nyloc
24 7077873 2 SCREW, #12-14 x 1/2” Hex Flange Self-Tap
25 7091594 2 COTTER PIN, 1/2” Self-Locking
26 7091686 2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
27 7034820 1 WELDMENT, Traction Lever, RH
28 7034821 1 WELDMENT, Traction Lever, LH
29 7043869 1 HANDLE, Loop (Weldment)
30 7029100 1 THROTTLE CONTROL, 40.50/1.46 used on Kawasaki 14HP &
Kohler 15HP
30 7072597 1 THROTTLE CONTROL, 51.50/0.90 used on Kawasaki 17HP
30 7036431 1 THROTTLE CONTROL, 48.50/0.90 used on Kohler 23HP
31 7012080 4 CABLE TIE, 7”
32 7073118 1 * WIRE HARNESS not shown; for all models except
for Kohler 23HP
32 7073117 1 * WIRE HARNESS not shown; used on Kohler 23HP
NOTE: * See Electrical Wiring pages for Illustration.