Chapter 8 – Prestart Inspection
S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834 41
0361259
PROPER USE OF SAFETY PROP
TO STORE SAFETY PROP
1. Remove all material from platform.
2. Raise platform until the open height is wide
enough to position the safety prop.
3. Place safety prop in the proper position.
4. Remove hands and arms from scissors area.
5. Lower platform until scissors are supported by
safety prop.
1. Raise platform until the open height is wide
enough to position the safety prop.
2. Place the safety prop in the storage position.
0361259
Death or serious injury
might result if safety prop
is not used and/or
properly positioned. Use
safety prop at all times
when servicing machine
with platform raised.
Proper position for safet y prop use
MODEL
NUMBER
EMPTY
VEHICLE
WEIGHT
MONTH / YEAR
OF MANUFACTURE
MAXIMUM
ALLOWABLE
MANUAL FORCE
(SIDE PULL)
MAXIMUM
GRADEABILITY
Indoors Outdoors
Do not remove any weight from this machine.
lbs
kg
deg
Snorkel International
2009 Roseport Road
Elwood, KS 66024
MAXIMUM
WHEEL
LOAD
MOTOR
BATTERIES
SLOPE SENSOR ALARM SETTING
deg
SIDE
TO SIDE
CHARGER
INPUT
SERIAL
NUMBER
lbs
kg
MAXIMUM
PLATFORM
HEIGHT
MAXIMUM
DRIVE
HEIGHT
ft
m
UNRESTRICTED
PLATFORM
CAPACITY
lbs
kg
MAXIMUM
ALLOWABLE
WIND SPEED
mph
m/s
lbs
N
FRONT
TO BACK
RATED NUMBER
OF OCCUPANTS
Indoors Outdoors
V
V
Ah
V
1501664
1502773/1502777/1502598/1502774/1502775/1502776
Turn the free-wheeling
valve counterclockwise to
the fully open position.
3.
Push and release the brake
release pump several times
to release the brakes.
4.
After moving the machine,
turn the brake release valve
fully counterclockwise.
Turn the free-wheeling valve
fully clockwise. Operate
the drive function to verify
that the brakes reset.
6.
DO NOT exceed 2 mph
(3.2 km/h) when towing.
5.
1.
Before towing, pushing, or winching, the machine must be on level
ground. Read and understand all instructions. Refer to the Operator’s
Manual. Turn battery disconnect switch to "OFF" position.
TOWING INSTRUCTIONS
DO NOT operate any hydraulic functions
after disengaging the brakes or the brakes
will reset, preventing the machine from
being moved.
DISENGAGE BRAKES
HYDRAULIC
MANIFOLD VALVE
Brake
Release
Valve
Turn the brake release valve clockwise to the fully closed position.
2.
1501533
Towing this machine requires disengaging the brakes. Follow instruction
below when towing, pushing, or winching this machine. Verify the brakes
have been reset after moving machine and before operating the machine.
DEATH OR SERIOUS INJURY COULD RESULT
FROM UNCONTROLLED MOTION.
WARNING
Free-Wheeling
Valve
Brake
Release
Pump
1501533
Right Side
Rear
1502773 – S3215L
1502777 – S3215E
1502598 – S3219E
1502777 – S3220E
1502774 – S3226E
1502775 – S4726E
1502776 – S4732E
1501475
0361259
300760
300760
DANGER
Trays must be closed when platform is elevated.
TIPOVER HAZARD
300760
DEATH OR SERIOUS INJURY MAY
RESULT IF MACHINE TIPS OVER
1501533
1501476
1501475
DEATH OR S ERIOUS I NJURY WILL RESULT FROM
TIPPI NG OVER. TO KEEP FROM TIPPING THIS
MACHINE OVER FOLLOW THESE RULES.
DO NOT RAISE OR DRIVE AN ELEVATED
PLATFORM ON A
SLOPE
GO NO CLOSER THAN
4 FEET (1.2 M) to
ANY DROP OFF
OR H OLE
4 FT
OTHER ACTIONS CAN ALSO CAUSE
THIS MACHINE TO TIP OVER
DO NOT
DO NOT
DO NOT
DO NOT
DO NOT
overri de safety devi ces.
overload t he machine.
stand or si t on guardrail s.
attach r opes or chains to guardrails.
carry loads outside the r ailing or use as a crane.
OK
1.
3.2.
ALARM MEANS TI POVER DANGER!
LOWER PLATFORM IMMEDIATELY
DO NOT
use this machi ne without the raili ngs and the
entry gate, chain or bar i n place. You coul d fall
out and hurt or kill your self.
DO NOT
use this machi ne if i t is not worki ng right, or if
any part of it is damaged, worn, or mi ssing.
An accident coul d cause injury or death.
NOTE: STUDY THE OPERATOR'S MANUAL
BEFORE OPERATING THIS MACHINE.
ELECTRICAL SHOCK CAN KILL YOU
This machine is not el ectricall y insulated.
Maintain 10 feet (3.1 m) minimum clearance
from elect rical power li nes and apparatus.
This machine wil l not protect you fr om shock.
1501475
1501476
DEATH OR S ERIOUS I NJURY WILL RESULT FROM
TIPPI NG OVER. TO KEEP FROM TIPPING THIS
MACHINE OVER FOLLOW THESE RULES.
DO NOT RAISE OR DRIVE AN ELEVATED
PLATFORM ON
SOFT OR UNEVEN
SURFACES
DO NOT RAISE THE PL ATFORM
IN WIND ABOVE 28 MPH (12. 5 M/S)
OTHER ACTIONS CAN ALSO CAUSE
THIS MACHINE TO TIP OVER
NOTE: STUDY THE OPERATOR'S MANUAL
BEFORE OPERATING THIS MACHINE.
ELECTRICAL SHOCK CAN KILL YOU
Allow for pl atform sway, rock, or sag.
If vol tage is 300 V to 50 kV, stay at least
10 feet (3. 1m) away.
If vol tage is more than 50 kV, talk with your
supervi sor or read the Operator 's Manual
on this machine for safe di stances.
1501476
DO NOT
DO NOT
let an unt rained or unauthorized person use this
machine. When leaving the machine unatt ended,
remove the key, turn the bat tery disconnect swi tch
off, and lock it in the off posi tion.
replace component s criti cal to machine stability,
such as batter ies and wheels, wit h lighter weight
or non-fact ory approved substi tutes.
TO AVO ID
TIPOVER HAZARDS
USE ON
FLAT, LEVEL, AND
SOLID SURFACES
ON LY
4 FT
OK
DO NOT
DO NOT
DO NOT
ride pl atform while machine i s on a truck, fork lif t
or other devi ce.
use ladder, sc affold, or ot her means to increase
size or pl atform height.
use with damaged ti res or wheels.
451986
DANGER
DO NOT ALTER OR DISABLE
LIMIT SWITCHES, SAFETY
SWITCHES, OR INTERLOCKS.
451986
451986
(Behind tray)
To Next Page
