Sony 300PF - Page 85

Chapter 4 Viewfinder Screen Indications and Menus 85
Chapter 4 Viewfinder Screen Indications and Menus
Advanced menu page 3

PAGE3 (NEXTm$ PREVm4)

mAWB MEM : 2
PRE. WHT : 3200
TONE : ON 
BARS : SMPTE
a)

REMOTE1 : REC
REMOTE2 : MARK
BAUD RATE: 38400 

EXIT MENU (YESmPUSH)
a) For DSR-300P: EBU75
Item
Settings
GAIN
This sets gain values for the positions of the GAIN switch.
The HIGH, MID, and LOW values must be set so that LOW
< MID < HIGH.
HIGH
Sets the H position.
3 dB, 6 dB, 9 dB, 12 dB, 18
dB (normal value), 18 dB +
DPR, 24 dB, 24 dB + DPR,
HYPER GAIN
MID
Sets the M position.
0 dB, 3 dB, 6 dB, 9 dB
(normal value), 12 dB, 18
dB, 18 dB + DPR, 24 dB, 24
dB + DPR
LOW
Sets the L position.
–3 dB, 0 dB (normal
value), 3 dB, 6 dB, 9 dB, 12
dB, 18 dB, 18 dB + DPR, 24
dB
DL
Sets DynaLatitude function
ON/OFF. This setting is
valid only when the
OUTPUT/DL/DCC+ switch
has been set to DL.
ON (normal value), OFF
When set to ON, the amount
of DynaLatitude effects is
set in basic menu page 2
(see page 79).
Advanced menu page 2

PAGE2 (NEXTm$ PREVm4)

GAIN
m HIGH: 18dB 
MID : 9dB 
LOW : OdB

DL : ON 


EXIT MENU (YESmPUSH)
Item
AWB MEM
Selects whether or not to
make the FILTER knob
settings (1 to 4) correspond
to separate white balance
adjustment values stored in
memory.
2 (normal value): No
correspondence with FILTER
knob settings. Only two
adjustment values (A and B)
are stored in memory.
2 × 4FL: Correspondence
with FILTER knob settings.
Each of the four knob
settings can be used to set A
and B adjustment values, for
a total of eight settings.
TONE
Selects whether or not to
output a 1-kHz audio signal
with the color bars when the
OUTPUT/DL/DCC+ has
been set to BARS.
ON (normal value): Output
audio signal.
OFF: Do not output audio
signal.
BARS
Selects normal width or
narrower width for color
bars.
SMPTE (normal value for
DSR-300): Normal width
EBU75 (normal value for
DSR-300P): EBU 75%
EBU100 (for DSR-300P):
EBU 100%
SPLIT (for DSR-300P): Not
for normal operation
SNG: Narrower than normal
(used for satellite
communications, etc.)
REMOTE1
Sets a function for position 1
of the RM-LG1 connected to
the REMOTE connector 1.
REC (normal value):
Specifies recording start/stop
MARK: Specifies a Mark IN/
OUT point.
CUE: Specifies a Cue point.
NG: Specifies NG/OK.
REMOTE2
Sets a function for position 2
of the RM-LG1 connected to
the REMOTE connector 1.
9600, 38400 (normal value)
REC: Specifies recording
start/stop.
MARK (normal value):
Specifies a Mark IN/OUT
point.
CUE: Specifies a Cue point
NG: Specifies NG/OK.
Settings
BAUD RATE
Sets a baud rate for a
computer connected to the
REMOTE connector 1 (to be
supported in future version).
PRE. WHT
Selects the color
temperature preset for the
white balance adjustment.
3200 (normal value):
3200 K
3000: 3000 K