To Next PageTo Next PageWhy won't my Sony DCR-TRV820 Camcorder turn on?
If your Sony Camcorder isn't powering on, make sure a charged battery pack is properly installed. Also, verify that the AC power adapter is correctly connected to a power outlet.
How to fix a blurry image on Sony DCR-TRV820 viewfinder screen?
If the image on your Sony Camcorder's viewfinder screen is blurry, try adjusting the viewfinder lens. Also, make sure that STEADYSHOT is set to ON in the menu. If FOCUS is set to MANUAL, switch it to AUTO. If the shooting conditions are not suitable for autofocus, manually adjust the focus by setting FOCUS to MANUAL.
Why does the START/STOP button not operate on my Sony Camcorder?
If the START/STOP button on your Sony Camcorder isn't working, there could be several reasons. First, ensure the POWER switch is set to CAMERA. Also, check if the tape has run out, and rewind or replace it if necessary. The write-protect tab might be exposing the red mark, so use a new tape or slide the tab. If moisture condensation has occurred, leave the camcorder for an hour to acclimatize. If the camcorder has been in standby mode for over 3 minutes, set the POWER switch to OFF (CHARGE) and then back to CAMERA. Adjust the viewfinder lens if needed. Ensure STEADYSHOT is set to ON in the menu settings and FOCUS is set to AUTO. If shooting conditions are unsuitable for autofocus, set FOCUS to MANUAL. Cancel any active digital effects. Finally, close the LCD panel.
What to do if my Sony DCR-TRV820 power keeps going off?
If your Sony Camcorder is shutting off unexpectedly, it could be due to a disconnected power source or a dead battery. Ensure the power source is connected and use a charged battery pack. Another cause might be moisture condensation; if this has occurred, leave the camcorder for an hour to acclimatize.
Why is there no sound when playing back a tape on my Sony DCR-TRV820?
If you're experiencing sound issues when playing back a tape on your Sony Camcorder, and the sound is low or absent, ensure that if you are playing a stereo tape, HiFi SOUND is set to STEREO in the menu settings. Also, check the volume level; open the LCD panel and press VOLUME + to increase it.
What to do if the tape doesn't move on my Sony DCR-TRV820?
If the tape isn't moving when you press a video control button on your Sony Camcorder, ensure the POWER switch is set to VTR. Also, check if the tape has run out and rewind it if necessary.
Why is SteadyShot not working on my Sony DCR-TRV820?
If the SteadyShot function isn't working on your Sony Camcorder, check if STEADYSHOT is set to OFF in the menu settings. If it is, set it to ON.
How to stop the demo mode on my Sony DCR-TRV820?
If your Sony Camcorder starts a demonstration after 10 minutes when the POWER switch is set to CAMERA or DEMO MODE is ON without a cassette, insert a cassette to stop the demonstration. Alternatively, you can cancel DEMO MODE in the menu settings.
Why can't I delete images from my Sony Camcorder?
If you can't delete an image on your Sony Camcorder, check if the write-protect tab on the “Memory Stick” is set to LOCK and release it. Also, verify if the image is protected and cancel image protection.
What to do if I cannot format the Memory Stick on my Sony Camcorder?
If you're unable to format the “Memory Stick” in your Sony Camcorder, it might be due to the “Memory Stick” being formatted incorrectly. Try formatting the “Memory Stick” on your camcorder or use another “Memory Stick.”
General| Type | Digital Camcorder |
|---|---|
| Digital Zoom | 120x |
| Focus | Auto/Manual |
| White Balance | Auto/Manual |
| Microphone | Built-in Stereo Microphone |
| LCD Screen | 2.5 inches |
| Video Output | Composite, S-Video |
| Battery Life | Approx. 1.5 hours |
| Viewfinder | Color |
Instructions for charging the battery pack and connecting AC power.
Procedure for inserting Hi8/Digital8 video cassettes.
Basic steps for recording video, including using the LCD and viewfinder.
How to monitor playback, control playback with remote, and use screen indicators.
Order of disassembly for the camcorder's main components.
High-level overview of the camcorder's internal circuitry and signal flow.
Essential preliminary steps and tool list before performing camera adjustments.
Information on accessing and using the camcorder's service mode for diagnostics and adjustments.
