Why is my Sony VCR Remote Commander not working?
If the Remote Commander or Remote Control Unit isn't working with your Sony VCR, check the setting of COMMANDER on the OTHERS menu and adjust it to match the device you are using.
Why is the time code not being recorded on my Sony DSR-45AP?
If your Sony VCR is not recording the time code of the input DV signal even when DV IN TC on the TC/UB SET menu is set to EXTERNAL, ensure REC MODE on the VTR SET menu is set to DVCAM. Also, confirm that the editing software you are using is outputting a time code and that the INPUT SELECT selector is set to DV.
What to do if duplication doesn't function on Sony DSR-45AP VCR?
If you're having trouble with duplication on your Sony VCR, check the STOP/CAUTION No. and any warning messages displayed on the LCD monitor, and take the appropriate action.
How to record using the Remote Control Unit on Sony DSR-45AP?
If you cannot make the Sony VCR record using the Remote Control Unit (DSRM-10/20), press the PLAY button while holding the REC button down on the Remote Control Unit.
Why does the pause mode release automatically on my Sony VCR?
To prevent the pause mode of recording, audio dubbing, or duplicating from being automatically released on your Sony VCR, note that the unit goes into stop mode after the pause mode continues for more than five minutes to protect the tape and video heads.
Why can't I do audio dubbing on my Sony DSR-45AP?
If you are experiencing issues with audio dubbing on your Sony VCR, ensure you are using a DVCAM-formatted tape that was recorded in the 32 kHz audio mode (4-channel). Audio dubbing onto DV-formatted tapes is not supported.
Covers fire, shock, and moisture hazards, and power connection requirements.
Essential guidelines for safe operation, installation, and maintenance.
Guidance on proper placement, ventilation, and owner record keeping.
Statements of FCC compliance for DSR-45A and DSR-45AP models.
Details on FCC testing, interference, user guidance, and general cautions.
Information regarding the disposal of mercury-containing lamps in the product.
Product compliance with EMC and Low Voltage Directives for European customers.
Guidelines for proper disposal of electrical equipment and batteries in the EU.
Warning about potential hearing loss from excessive sound pressure.
Highlights DVCAM format, high picture quality, wide track pitch, and PCM audio for professional use.
Details on DV format compatibility, cassette size options, and remote control capabilities.
Describes high-speed search, digital slow playback, TBC, jog audio, and various interface connectors.
Covers built-in LCD, duplication, audio dubbing, menu system, and easy maintenance functions.
Identifies and describes controls on the front panel, including cassette compartment and transport controls.
Detailed explanation of functions for ON/STANDBY, TIMER, AUDIO MONITOR, RESET, INPUT SELECT selectors.
Description of the LCD monitor and the character display selector for outputting data.
Explanation of DISPLAY SELECT, EXEC/FINE, and navigation buttons for menu and data adjustment.
Detailed functions of STOP, REW, PLAY, FF, PAUSE, REC, DUP, and AUDIO DUB buttons.
Further details on REC, AUDIO DUB, and DUP buttons, including operational notes and limitations.
Explanation of AUDIO INPUT switch and AUDIO REC LEVEL controls for adjusting recording levels.
Description of display window elements: SEARCH buttons, indicators, time counter, and selector.
Details on TC connectors, MONITOR jacks, remote control section, AC IN connector, and signal input selectors.
Explanation of Time Code (TC) connectors and DV jack, including connection notes and specifications.
Description of AC IN, CONTROL S IN, and MONITOR jacks, with notes on signal output.
Details on S VIDEO, VIDEO, and COMPONENT connectors for video signal input/output.
Explanation of INPUT LEVEL selector and AUDIO IN/OUT jacks for audio signal management.
Description of RS-232C, RS-422A, LANC jacks, and the Remote selector for unit control.
Explanation of EJECT, SEARCH, PLAYBACK SPEED, PAUSE, REW, PLAY, STOP, and REC buttons.
Details on FF, INDEX WRITE, and DATA CODE buttons for searching and data management.
Functions of INDEX WRITE and DATA CODE buttons for marking and displaying tape data.
Instructions for installing and replacing batteries in the remote commander, with notes on battery care.
How to display data on LCD/monitor, access menu screen, and understand data screen information.
How to display and interpret audio levels, channel status, and audio dubbing symbols.
Information on usable cassettes, cassette memory, saving recordings, and checking/inserting/ejecting cassettes.
Details on copyright, format differences, color systems, and playback/recording limitations.
Connecting the unit to digital video equipment via DV jack for high-quality playback.
Connecting the unit to video equipment without DV jack using analog signals.
Steps for setting up and initiating playback, stop, or pause functions.
How to check recorded data codes such as date/time and camera data during playback.
Using remote commander for variable speed playback and various search functions.
Details on search methods and setting up Auto Repeat playback.
Using an external AC timer to automate playback start and stop for repeated playback.
Connecting the unit to digital video equipment via DV jack for high-quality recording.
Connecting the unit to video equipment without DV jack using analog signals.
Selecting input signals, audio modes, and adjusting audio recording levels.
Procedures for starting recording and marking index signals for easy scene searching.
Using an external AC timer to automate recording start at a preset time.
General limitations and specific notes on using the unit within an editing system.
Configuration settings for various editing controllers (FXE, BVE, RM) for optimal integration.
Connecting the unit to an editing controller for digital non-linear editing.
Diagram showing the unit as a player in a cut editing system.
Settings for editing control units and the DSR-45A/45AP player/recorder.
Example configuration diagram for an A/B roll editing system.
Details on connecting reference video signals for stable editing and synchronized playback.
Connecting control signals and video/audio signals for A/B roll systems.
Setting up connections to monitor video and audio signals on a video monitor.
Steps for adjusting edit timing with various controllers (RM, PVE, FXE).
Procedure for fine-tuning the edit IN point if actual edited point does not coincide with preset.
Steps for adjusting edit timing with BVE-600/2000 controllers, including sync grade and device constants.
Overview of setting, displaying, recording, and outputting time code and user bits.
How to set the initial time code value and record data using the internal generator.
Step-by-step guides for setting time code and user bits using the unit's menu system.
Options for recording internal or external time code and user bits, including DV signal recording.
Selecting time code recording mode (REGEN/PRESET) and advancement mode (REC RUN/FREE RUN).
Setting the frame mode (DF/NDF) and controlling time code output during jog playback.
Diagram and steps for connecting an external time code generator for synchronization.
Procedure to verify that the internal time code is synchronized with the external time code.
Table detailing time code output and recording based on TC/UB IN and INPUT SELECT settings.
Details on time code output limitations, synchronization methods, and conditions for FREE RUN.
Steps for adjusting sync and subcarrier phases using a vectorscope for NTSC and PAL signals.
Using H PHASE, H PHASE F, SC PHASE, SC PHASE F menus for phase alignment.
How to adjust Y, R-Y, and B-Y signal levels using the PB LEVEL setting.
How to adjust chrominance signal gain for composite signals using the PB LEVEL setting.
Copying time codes and data, and selecting duplicate modes (AUTO/MANUAL).
Procedure for duplicating tapes using AUTO modes, including standby and start steps.
Procedure for duplicating tapes from any point using MANUAL mode, including start point adjustment.
How the unit detects and skips blank portions on the source tape during duplication.
Table of common error messages and their causes/remedies during the duplication process.
Additional warning messages related to cassette memory, tape length, and player/recorder status.
Basic connection for audio dubbing and choosing input channels (1/2 or 3/4).
Step-by-step guide to dubbing sound onto a tape, including level adjustment and monitoring.
Introduction to using the unit's menu system for parameter adjustment and settings.
Procedure for navigating menus and understanding the overall menu structure.
Settings for TC PRESET, UB PRESET, and TC/UB IN options related to time code and user bits.
Settings for DV IN TC, TC MAKE, TC RUN, and TC FORMAT for time code management.
Options for LOCAL ENBL, PREROLL, POST CUEUP, STILL DLY, and 232C RATE for remote control.
Settings for CM SEARCH, TITLE DISP, LABEL DISP related to cassette memory scene search.
Procedure for creating a tape label by entering characters on the unit.
How to erase specific items like index, title, date, or photo data from cassette memory.
Procedure to erase all items stored in the cassette memory.
Options for displaying data codes and selecting EE or PB mode for image and sound output.
Settings for displaying color bars and adjusting the font size of menu lines.
Selecting the format for displaying dates (Y/M/D) and times (24H/12H).
Adjusting noise reduction levels for luminance (PB YNR) and chrominance (PB CNR) signals.
Adjusting video signal levels (PB LEVEL) and sync/subcarrier phases (H PHASE, SC PHASE).
Setting external sync and fine-tuning phase adjustments for video signals.
Selecting audio modes (FS32K/FS48K) and input channels for audio dubbing (CH1,2/CH3,4).
Controlling jog audio output and setting reference levels for audio meters.
Configuring Auto Gain Control (AGC) linking/separation and enabling/disabling the limiter.
Selecting recording mode (DVCAM/DV SP) and auto index marking for recordings.
Configuring still picture display modes and tape transport speeds for FF/REW operations.
Selecting duplicate mode and DV EE output settings for signal transmission.
Setting STILL TIME and FROM STILL options for tape protection in still mode.
Selecting control device (Remote Commander/Control S) and configuring auto standby behavior.
Adjusting LCD brightness/color and setting the unit's internal clock.
Guidance for resolving common problems like power issues, unit not operating, and cassette loading errors.
Solutions for duplication failures, unavailable menu items, unit operating by itself, and inaccurate edit timing.
Resolving issues with audio dubbing, noisy audio, and EE picture/sound output problems.
Addressing issues with playback pause release, auto standby, tape rewind, and unit starting automatically.
Adjusting input levels, resolving non-linear editing system issues, and locating editing points.
Resolving issues with LCD monitor display and unit operation via connected devices or remote control.
Table of alarm messages displayed on LCD, beep codes, and display window indicators.
Guidelines on environmental conditions, placement, ventilation, and handling to prevent damage or malfunction.
Information on checking video heads every 1000 hours and cleaning them to maintain picture quality.
Notes on cassette memory function, terminal cleaning, label affixing, and LCD screen care.
Understanding moisture condensation issues and how to handle the unit after temperature changes.
Using the digital hours meter for maintenance scheduling and understanding the self-diagnostics function.
Comparison of DVCAM and DV formats, including track pitch, sampling frequency, and time code systems.
Information on using DVCAM and DV cassettes with different recorder formats.
Information on which tapes can be played on DVCAM or DV equipment.
How DV connections affect recording format and compatibility for editing.
How the unit handles wide-screen aspect ratio information during input and playback.
Details on recording format, video signals, quantization, sampling frequency, and connectors.
Information on audio quantization, sampling frequency, usable cassettes, and recording times.
Details on clock system, power backup, operating temperature, dimensions, mass, and supplied accessories.
Specifications for remote control interfaces and LCD screen.
Definitions for audio modes, signals, clipping, component, composite, and condensation.
Definitions for drop frame, EE mode, head drum, loading, luminance, search mode, SMPTE.
Definitions for subcarrier, superimpose, S-video, sync signal, TBC, threading, time code, unloading.
Definitions for 12-bit (Fs32k) and 16-bit (Fs48k) audio recording modes.
To Next Page
General
