Sony MDS-E12 - Playing MDs; Operations you may want to do during CD; Playing a Specific Track

H
rf
é
8
z
g
S
&
z
g
Operations you may want to do during CD
to Press
Stop recording CD-SYNCHRO STOP
Pause recording CD-SYNCHRO STANDBY
Locate the next track to CD PLAYER He /P Pi
be recorded during
recording pause
Resume recording CD-SYNCHRO START
after pausin;
Check the remaining. ‘TIME of the recorder
recordable time on the MD
YH Youcan use the remote of the CD playerduring CD Synchro-
recording
Press To change the And change the
recorder to CD player to
> Recording Play
) Recording pause Stop
i Recording pause “Pause
& Youcan change CDs during CD Synehro-reconding
1 Press @ on the CD player's remote.
2 Change the CD.
3 Press > on the CD player's remote.
Recording resumes.
Notes
* When performing CD Synchro-recording with a CD
player with a mode selector, be sure to set the selector to
CDI.
* When you record tracks from certain CD ot multi-disc
players, the entire material may be recorded as a single
track.
2 a
WY Youcanadjustthe analog signal output level.
1 While the recorder is playing, press LEVEL/DISPLAY/
CHA (or DISPLAY) repeatedly until the line output
adjustment display appears.
2 Tum AMS (or press LEVEL +/— repeatedly) to adjust
the output signal level.
F Youcanuse Setup Menu to adjust the analog outputievel
1 Press MENU/NO twice.
“Setup Menu” appears in the display.
2:Turn AMS (or press Md /SP1 repeatedly) to select
“Output Level,” then press AMS or YES.
3 Turn AMS (or press hed />P1 repeatedly) to adjust the
output level, press AMS or YES.
4 Press MENU/NO,
Y Youcanmake EJECT not function during play or pause to
avoidejetting the MD by mistake.
4 Press MENU/NO twice during stop.
“Setup Menu” appears in the display.
2 Tum AMS (or press Hid /PPI repeatedly) to select
“Play Pause,” then press AMS or YES.
3 Turn AMS (or press Ket /PPI repeatedly) to select "&
Disable,” then press AMS or YES.
4 Press MENU/NO.
‘To function EJECT, select “# Enable” in step 3.
ty 8
Playing a Specific Track
While the recorder is playing, pause or stopped, use the
procedure below to quickly play any track.
Te goto De the following:
The nextor a succeeding Tum AMS clockwise (or press
track during play PPI repeatedly).
A preceding track Tum AMS counterclockwise
during play (or press tet repeatedly).
‘The beginning of the “Turn AMS counterclockwise
current track during play __(or press Mil once),
A specific track while the 1 Tum AMS (or press td /
recorder is stopped Pi repeatedly) until the
track number appears in the
display.
2 Press AMS or Di.
* Automatic Music Sensor
Y Tolocate thetast track of the MD quickly
While the recorder is stopped, turn AMS
counterclockwise (or press 4 once).
© Ifyoutocate a track whllethe recorderis stopped or paused
The recorder will still be stopped or paused at the
beginning of the located track.
ee Oe
Playing an MD
POWER AMS
1 Turn on the mixer.
2 Adjust tha fader or level of tha connected channel
of the mixer,
3 Press POWER to turn on the recorder,
4 Insert an MD.
5 lfnecessary, turn AMS (or press betel /> 4
repeatedly) to locate the track you want to start
playing from.
If you want to play from the first track, go to step 6,
6 Press Pt.
The recorder starts playing.
Operations you may want to do during play
To Press or turn.
Stop play a
Pause pla} bu
Resume play after pausing Di
Locate a succeeding track AMS clockwise (or press Pt
repeatedly)
Locate the beginning of AMS counterclockwise (or
the current track or press Kd repeatedly)
a preceding track
Eject the MD- After stopping play &
Y Toplay the MD on which LP2, LPs stereo recording or MONO
recording has been performed
By pressing Pit in step 6 above, “LP2," “LP4,” or
"MONO" lights up depending on the mode recorded
on the lower left of the display window.
BEER :
eB ASSS:
Y rouse
Connect them te PHONES jack, Tam PHONE LEVEL
to adjust the volume.
Press the number button(s) to enter the track number of
the track you want fo play.
To enter a track number over 26
1 Press >25.
See the examples below for the number of presses.
2 Enter the corresponding digits.
To enter 0, press 10 instead.
Examples:
¢ To play track number 30, press >25, then 3 and 10,
* To play track number 108, press >25 twice, then 1, 10,
and 8,
Y ttyou entera track number while the recorder is paused
The recorder will be paused at the beginning of the
track.
Saw Surkeg i
If MSCAN fs pressed during stop, the beginning of each
track is played sequentially only at the set fix time.
Press &> for the track you want to monitor.
Y Youcanadjustthe playtime for the beginning ofa trackby
MUSICSCAN
1 Press MENU/NO twice,
“Setup Menu" appears in the display.
2 Turn AMS (or press Ht<4 /PP4 repeatedly) to select
“Music Scan,” then press AMS or YES.
3 Turn AMS unt! the desired time of 6 to 20 seconds
appears in the display, then press AMS or YES.
4 Press MENU/NO.
29