Sony SNC-RZ25 User Manual

UNI-OFL7C2
Outdoor and Indoor Recessed Dome Housings
Installation and Operation Instructions for the following model:
UNIOFL7C2 Outdoor Recessed Housing, clear dome, 24Vac input, Heater/ Blower
Note: AC 24V power supply for the camera and the heater/blower is an installer/reseller provided item.
Please refer to Camera Manual for power consumption details.
Note: Please note that to achieve the increased depth with the aspheric design for optimal camera
lens to capsule orientation, the capsule is slightly angled around the highest section.
This creates a ”line’, visible to the naked eye, around the upper most section of the capsule.
This “line”serves as the geometric center line used to insure proper camera placement. It is
not typically seen by the camera. However, Sony RZ series PTZ cameras are able to tilt up
above the horizon to 25°, this wide range of tilt motion at a wide angle view may cause this line
to be captured in the image.
Mounting instructions for:
SNC-RZ25
SNC-RZ30
SNC-RZ50
SNC-RX530
SNC-RX550
SNC-RX570
SNC-RH124
SNC-RS44
SNC-RS46
81-IN6525
10/14/2009
Quick Reference: Camera Installation Steps
SNC-RZ25N............................Go to Steps 3-5
SNC-RZ30N............................Go to Steps 6-8
SNC-RZ50N............................Go to Steps 9-11
SNC-RX Series........................Go to Steps 12-18
SNC-RH/RS.............................Go to Steps 19-26

Sony SNC-RZ25 Specifications

General

Effective Pixels	380, 000 pixels
Network Interface	10Base-T/100Base-TX
Power Supply	AC 24V
Connectivity Technology	Wired
Digital Zoom	12x
Frame Rate	30 fps
Video Modes	NTSC, PAL
Voltage Required	AC 24V
Sensor Type	CCD
Signal System	NTSC/PAL
Day/Night	Yes
Power Requirements	AC 24V
Camera Type	Network Camera
Lens Type	Varifocal
Pan Range	360°
Video Compression	JPEG, MPEG-4
Max Aperture	F1.6
Protocols	HTTP, FTP, SMTP, DHCP, DNS, NTP
Power Device	Power adapter
Operating Temperature	-10°C to +50°C

Summary

Mounting Instructions and Quick Reference

Mounting Instructions for Cameras

Lists camera models for which mounting instructions are provided.

Quick Reference: Camera Installation Steps

Provides a quick guide to installation steps for various camera models.

Important Safety Information

Important Safeguards

Outlines essential safety and operating instructions for the unit.

Safety Precautions

Details safety precautions, including hazard symbol explanations.

Unpacking Procedures

Instructions on how to carefully unpack the electronic components.

Service Information

Provides contact information for technical support and service needs.

Box Contents

Contents of Box Details

Illustrates and lists the specific items included in the package.

Specifications and Component Location

Electrical Specifications

Details power requirements, including voltage and wattage.

Operating Temperature Specifications

Specifies the acceptable operating temperature range for the housing.

Location of Housing Components

Identifies the positions of key components within the housing.

Maximum Cable Distances

Recommended Distances for 24VAC

Provides maximum cable distances for 24VAC with a 10% voltage drop.

Power and Control Input Connections

Power and Control Inputs (Outside of Housing)

Details the power and control input ports and their pin assignments.

Adding Jumpers for Power Supply

Instructions on adding jumpers for a common power supply.

Camera Installation and Wiring

Steps for installing the camera and completing wiring applications.

Replacement Parts

Replacement Parts List

Lists all available replacement parts with their part numbers.

Dome Bubble Cleaning

Materials Needed

Lists the necessary materials for cleaning the dome bubble.

Cleaning Dome Exterior

Step-by-step guide for cleaning the exterior of the dome bubble.

Cleaning Dome Interior

Step-by-step guide for cleaning the interior of the dome bubble.

Warranty Information