Sony SRF-M100 - Setting the Clock; Preset Tuning

Setting the Clock
When you set the clock, turn off the radio.
1 While keeping ENTER/CLOCK pressed, press
TUNE/TIME SET + or — button until the
display shows the current time.
Press + to increase or — to decrease the
digits. When you keep the button pressed,
the digits change rapidly.
While setting the
time, “:" is flashing. 0:00 = midnight
12:00 = noon
2 When the display shows the current time,
release ENTER/CLOCK.
“?" stops flashing and the clock starts
operating.
To set the clock to the second
After adjusting the time, keep ENTER/CLOCK
pressed. Release ENTER/CLOCK using the
time signal as a reference.
eee ule Mm UC Mteleom D | 2
1 While pressing the green button, slide AUTO
’ OFF/POWER to the direction of the A mark
to turn on the power.
2 Select FM or AM with BAND.
3 Tune in the desired station by pressing
TUNE/TIME SET + or — button.
At each press of + or —, the FM frequency
changes by 0.05 MHz higher or lower (the
display changes by 0.1 MHz) and the AM
frequency changes by 9 kHz higher or lower.
To change the frequency rapidly, keep the
button pressed.
4 Adjust VOLUME.
To turn off the radio
Slide AUTO OFF/POWER again.
The display shows the current time.
When the power is turned off automatically
The radio will be turned off automatically after
about 90 minutes to prevent unnecessary wear
of the batteries. To continue listening to the
radio, slide AUTO OFF/POWER again. If the
batteries are exhausted, the power is turned
off automatically to protect the preset
contents.
To receive a stereo program in stereo
Use the earphones. The sound coming through
the speaker is monaural.
Preset Tuning
Once you store the desired stations, you can tune them in by a simple operation. You can store
7 stations for each of the FM and AM bands.
Presetting the Station [4
1 Turn on the power.
2 Tune in the desired station to preset.
See “Operating the Radio”. .
3 Keep ENTER/ICLOCK pressed for more than
1 second.
Release ENTER/CLOCK when PRESET and
the preset number indicator flash in the
display window with the beep sound.
4 Select a preset number from 1 to 7 by
pressing the PRESET + or — button.
Press + to increase the digit.
(12>... . +67)
to
Press — to decrease the digit.
(7>6—>. .. . -*2->1)
| eae ee ee
5 Press ENTER/CLOCK again.
Beep-beep sounds, and PRESET and the
preset number stop flashing.
The station has been stored.
To preset other stations, repeat steps 2 to 5.
Note
Go to the next step while the PRESET and
preset number are flashing (for about 5
seconds). Otherwise the unit returns to step 2.
If this happens, try again from step 3.
Tuning in a Preset Station jj
1 Turn on the power.
2 Select the band, FM or AM.
3 Select the desired preset number by pressing
the PRESET + or — button.
4 Adjust VOLUME.
To change the preset station
Tune in the desired station to be newly preset.
Preset the tuned station to the desired button.
The station previously preset to that button is
canceled.
To Improve Radio Reception
FM: Extend the telescopic antenna and adjust
the angle of the antenna so that the FM
sensitivity will be increased.
AM: A ferrite bar antenna is built in for AM
reception. Rotate the unit horizontally for
optimum reception.
If the FM stereo program is noisy
Usually set STEREO/MONO to STEREO. You
can receive the FM stereo program in stereo,
using the earphones. When the signal is
weak and noisy, set it to MONO. There will
be no stereo effect, but the sound will
improve.