Sony STR-D965 - Presetting Radio Stations

“C¥
If
you
cannot
tune
ina
station
and
the
entered
numbers
are
flashing
Make
sure
you've
entered
the
right
frequency.
If
not,
press
DIRECT
and
re-enter
the
frequency
you
want.
If
the
entered
numbers
still
flash,
the
frequency
is
not
used
in
your
area.
xa}
To
watch
FM
simulcast
TV
programs
Make
sure
that
you
tune
in
the
simulcast
program
both
on
the
TV
(or
the
VCR)
and
on
the
receiver.
cay
If
you
enter
a
frequency
not
covered
by
the
tuning
interval
The
entered
value
is
automatically
rounded
up
or
down
to
the
closest
covered
value.
Tuning
intervals
for
direct
tuning
are:
FM: 50 kHz intervals
AM:
10
kHz
intervals
(to
change
to
9
kHz
intervals,
see
page
22)
Receiving
broadcasts
by
scanning
stations
(automatic
tuning)
If
you
don’t
know
the
frequency
of
the
radio
station
you
want,
you
can
have
the
receiver
scan
all
the
receivable
stations
to
locate
the
one
you
want.
1° ~Press TUNER.
The
last
received
station
is
tuned
in.
2
Press
DISPLAY
so
that
“NORMAL
MODE”
appears
in
the
display.
3
Press
BAND
to
select
FM
or
AM.
@
Press
TUNING/INDEX
SELECT
+
or
-.
Press
the
+
button
for
a
higher
station
number;
press
the
—
button
for
a
lower
one.
When
you
tune
past
either
end
of
the
band,
the
receiver
automatically
jumps
to
the
opposite
end
and
continues
scanning
in
the
same
direction.
Every
time
a
station
is
received,
the
receiver
stops
scanning.
To
continue
scanning,
press
the
button
again.
¢
If
scanning
stops
too
frequently
(for
FM
band
only)
Skip
the
stations
with
weak
signals.
Press
LEVEL.
“HIGH”
appears
in
the
display
and
the
receiver
scans
only
stations
with
strong
signals.
Receiver Operations
Presetting
Radio
Stations
You'll
most
likely
want
to
preset
the
receiver
with
the
radio
stations
you
listen
to
often
so
that
you
don’t
have
to
tune
in
the
station
every
time.
The
receiver
can
store
a
total
of
30
FM
or
AM
stations.
You
can
store
the
stations
on
preset
numbers
combining
3
characters
(A,
B
and
C)
and
numbers
(0-9).
For
example,
you
can
store
a
station
as
preset
number
A1,
B6,
or
C9.
Numeric buttons MEMORY
SHIFT TUNER
1° Press TUNER.
The last received station is tuned in.
2 = Tunein the station you want.
If you are not familiar with how to tune in a station,
see “Receiving Broadcasts” on the previous page.
3 Press MEMORY.
“MEMORY” appears for a few seconds.
Do steps 4 and 5 before “MEMORY” goes out.
4 Press SHIFT to select a memory page (A, B or C).
Each time you press SHIFT, the letter “A”, “B” or
“C” appear in the display.
5 Press the number you want to use (0 to 9).
If “MEMORY” goes out before you specify the preset
number, start again from step 3.
6 Repeat steps 2 to 5 to preset other stations.
To change a preset station
Preset anew station on the number you want to change.
Note
If the AC power cord is disconnected for more than one month,
the preset stations will be cleared from the receiver's memory,
and you will have to preset the stations again.
(continued)
11