Why there is no sound from the active sub woofer of Sony Stereo Receiver?
There is no sound output from the SUB WOOFER terminal on your Sony Stereo Receiver depending on the selected sound field.
Why is my Sony Stereo Receiver remote not working?
If your Sony Stereo Receiver remote isn't working, ensure you're pointing it at the remote sensor on the receiver and that there are no obstacles in the way. Verify the remote's mode matches the receiver's. If the batteries are weak, replace them. Also, make sure you've selected the correct function on the remote. Note that the AUX, SOURCE, MPX/DUAL, 12 and ON SCREEN buttons on the remote are not available. Press MAIN MENU on the remote before you use the V/v/B/b buttons for receiver operation.
How to fix hum or noise on Sony Stereo Receiver?
If you're experiencing severe hum or noise with your Sony Stereo Receiver, first ensure that the speakers and components are securely connected. Check that connecting cords are away from transformers, motors, TVs, or fluorescent lights (at least 3 meters away). Move your TV further from the audio components. If you have a turntable connected, ensure the U SIGNAL GND terminal is grounded. Finally, clean the plugs and jacks with a cloth slightly moistened with alcohol.
How to improve FM reception on my Sony Stereo Receiver?
If the FM reception on your Sony Stereo Receiver is poor, try connecting the receiver to an outdoor FM antenna using a 75-ohm coaxial cable (not supplied). Ensure the outdoor antenna is grounded against lightning, but do not connect the ground wire to a gas pipe to prevent gas explosion. If the signal strength of the stations is too weak, use direct tuning. Make sure you set the tuning interval correctly (when tuning in AM stations with direct tuning). Preset the stations if no stations have been preset or the preset stations have been cleared. Press DISPLAY so that the frequency appears in the display.
What to do if there is no sound from a specific component on my Sony Stereo Receiver?
If there's no sound from a specific component connected to your Sony Stereo Receiver, check that the component is correctly connected to the appropriate audio input jacks. Ensure the cords used for the connection are fully inserted into the jacks on both the receiver and the component. Also, verify that you have selected the correct component on the receiver.
What to do if FM reception is poor on Sony Stereo Receiver?
If the FM reception on your Sony Stereo Receiver is poor, use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna. Also, make sure you select the correct function on the Receiver remote.
What to do if there is no sound from center or surround speakers of Sony Stereo Receiver?
If there is no sound or very low-level sound from the center and/or surround speakers on your Sony Stereo Receiver, ensure the sound field function is activated by pressing MODE (SOUND FIELD). Choose a sound field containing “CINEMA STUDIO EX”. Adjust the speaker levels. Also, verify that the center and/or surround speaker size parameter is set to either “SMALL” or “LARGE”.
Why there is no sound from a specific component on my Sony Stereo Receiver?
If you are not getting sound from a specific component connected to your Sony Stereo Receiver, check that the component is properly connected to the correct audio input jacks on the receiver. Ensure the cords used for the connection are fully inserted into the jacks on both the receiver and the component. Also, make sure you have selected the correct component on the receiver.
How to fix recording issues on Sony Stereo Receiver?
To resolve recording issues with your Sony Stereo Receiver, verify that all components are correctly connected. Select the source component using the FUNCTION control. Before recording from a digital component connected to the analog MD/TAPE terminals, ensure INPUT MODE is set to 'ANALOG 2CH FIXED'. When recording from a digital component connected to the DIGITAL MD/TAPE OUT terminals, make sure INPUT MODE is set to 'COAXIAL FIXED' or 'OPTICAL FIXED'.
Why is there no picture on my Sony Stereo Receiver?
If there is no picture or an unclear picture on the TV screen or monitor connected to your Sony Stereo Receiver, select the appropriate function on the receiver. Set your TV to the appropriate input mode. Move your TV away from the audio components.
Instructions for connecting FM and AM antennas to the receiver.
Diagrams and instructions for connecting audio sources like turntables, CD players, and tape decks.
Guidelines for connecting video sources like TVs, VCRs, and DVD players.
How to connect digital audio sources like DVD and satellite tuners for surround sound.
Connecting front, surround, center, and subwoofer speakers to the receiver.
Resetting all receiver settings to factory defaults.
Adjusting speaker settings like size, distance, and crossover frequencies.
Setting the size (LARGE/SMALL/NO) for front speakers and its implications.
Setting the size (LARGE/SMALL/NO) for the center speaker.
Setting the size (LARGE/SMALL/NO) for surround speakers.
Selecting YES or NO for sub woofer connection and its effect on bass redirection.
Setting the distance from listening position to front speakers.
Setting the distance from listening position to the center speaker.
Setting the distance from listening position to surround speakers.
Verifying that all component and speaker connections are correct.
Choosing the input source or component to use.
Auto-detecting and decoding various audio signal formats.
Choosing from pre-programmed sound fields for different listening experiences.
Using Cinema Studio EX modes to reproduce movie theater sound characteristics.
Choosing from a variety of sound fields like Mono Movie, Stereo Movie, Concert Hall, etc.
Choosing the decoding mode for surround back signals for 6.1 channel sound.
Customizing surround effects like effect level, wall type, and reverberation.
Adjusting the overall presence of the surround effect.
Adjusting the balance between front left and right speakers.
Adjusting bass, midrange, and treble for each speaker and sound field.
Adjusting bass and treble levels for surround and surround back speakers.
Manually entering radio station frequencies for tuning.
Scanning for available radio stations automatically.
Overview of buttons on the RM-PG411 and RM-PP411 remotes.
Learning remote control codes for non-Sony or unsupported components.
Safety, power source, heat, placement, operation, and cleaning guidelines.
Common problems and solutions for audio, connection, and recording issues.
Details on power output, harmonic distortion, and frequency response.
General| Channels | 5.1 |
|---|---|
| Total Harmonic Distortion (THD) | 0.09 % |
| Frequency Response | 10 Hz - 100 kHz |
| Inputs | 4 x Audio, 2 x Digital Optical, 2 x Digital Coaxial, 1 x Phono, 1 x Video |
| Weight | 13.2 kg |
| Input sensitivity | 200 mV |
| Output | 100 W per channel |
| Speaker load impedance | 8 ohms |
| Speaker Impedance | 8 ohms |
| Preset Stations | 30 |
| Tuning range | AM/FM |
| Power Output (RMS) | 100W per channel |
| Power output | 100W per channel |
| Outputs | 1 x Audio, 1 x Video |
| Signal to noise ratio | > 98 dB |
| Digital inputs | coaxial, optical |
| Dimensions | 43 cm x 40.1 cm x 15.75 cm |
| Signal-to-Noise Ratio | > 98 dB |
| Tuner Type | AM/FM |
| Audio Inputs/Outputs | 4 x Audio Inputs, 1 x Audio Output |
| Digital Audio Inputs | Coaxial, Optical |
| Video Inputs/Outputs | 3 inputs, 1 output |
To Next Page
