D
Darryl BellAug 28, 2025
What to do if my 3D image is not displayed on Sony STR-DA2800ES Receiver?
- Zzachary72Aug 29, 2025
If a 3D image is not displayed on your Sony Receiver, check the 3D image formats supported by the receiver.
To Next PageTo Next PageWhat to do if my 3D image is not displayed on Sony STR-DA2800ES Receiver?
If a 3D image is not displayed on your Sony Receiver, check the 3D image formats supported by the receiver.
Why is multi-channel sound not outputting from my Sony Receiver?
If multi-channel sound cannot be output from your Sony Receiver, and “Control for HDMI” is set to “On,” “Audio Out” may be automatically set to “AMP.” In this case, set “Audio Out” to “AMP.”
How to fix severe hum or noise on Sony STR-DA2800ES Receiver?
If you are experiencing severe hum or noise with your Sony Receiver, check that the speakers and equipment are connected correctly. Ensure connecting cords are away from transformers, motors, TVs, or fluorescent lights. Move your TV away from the audio equipment. If the plugs and jacks are dirty, wipe them with a cloth slightly moistened with alcohol.
What to do if the lighting device cannot be operated with my Sony STR-DA2800ES Receiver?
The device may be updating its software, so wait for about half an hour until the update is completed. It may be off-line, so wait for half an hour until the device returns online. Reset the lighting device and delete the identified device on the receiver. Reboot the receiver and then set up the Lighting Control function again.
Why is the top of my Sony STR-DA2800ES hot?
The top of the Sony Receiver getting hot is not a malfunction.
What to do if when the Zone2 Out function is enabled and you select the same HDMI input for both the main zone and zone 2, there may be some interference on the audio with my Sony Receiver?
To avoid possible interference in the main zone, you can place priority on the main zone for HDMI input selection.
What to do if the Universal Remote Control function does not work on my Sony Receiver?
Make sure the connections required are made. Press ?/1 on the remote control to turn the receiver off and then on again. Hold down ?/1 on the receiver until the lamp above the button flashes in green to reboot the receiver. If the remote sensor of the receiver and that of another Sony product face the same direction, interference may occur. In this case, set the remote sensors so that they face different directions or use an IR shield on the other Sony product to shield the IR from interference from the receiver IR remote.
What to do if my Sony Receiver is overheating?
If the top of your Sony Receiver is hot, this is specific to this amplifier and is not a malfunction.
Why does my Sony STR-DA2800ES Receiver turn on automatically?
If your Sony Receiver is turning on automatically, it might be due to the “Control for HDMI” being set to “On” or “Pass Through” being set to “Off.” In this case, the receiver may be turned on by operating other equipment connected to it.
What to do if there is no sound on my Sony STR-DA2800ES Receiver?
If there is no sound from your Sony Receiver, verify that the speakers and equipment are correctly connected and turned on. Ensure the MASTER VOLUME is not set too low (try around -40 dB). Check that SPEAKERS is not set to OFF. Also, make sure the muting function is not enabled, headphones are not connected, and the correct input is selected. If you want to listen to the sound from the TV speaker, set “Audio Out” to “TV+AMP” in the HDMI Settings menu.
General| Bi-amping | Yes |
|---|---|
| Night mode | No |
| Sample rate | 192 kHz |
| Product color | Black |
| Connector contacts plating | Nickel |
| Case or master carton weight | 15 kg |
| Power consumption (standby) | 0.5 W |
| Power consumption (typical) | 290 W |
| Dimensions (WxDxH) | 500 x 258 x 487 mm |
| Total Harmonic Distortion (THD) | 0.09 % |
Weight and Dimensions| Weight | 12400 g |
|---|
