Why is multi-channel sound not outputting from my Sony Receiver?
If multi-channel sound cannot be output from your Sony Receiver, and “Control for HDMI” is set to “On,” “Audio Out” may be automatically set to “AMP.” In this case, set “Audio Out” to “AMP.”
What to do if there is no sound on my Sony STR-DA2800ES Receiver?
If there is no sound from your Sony Receiver, verify that the speakers and equipment are correctly connected and turned on. Ensure the MASTER VOLUME is not set too low (try around -40 dB). Check that SPEAKERS is not set to OFF. Also, make sure the muting function is not enabled, headphones are not connected, and the correct input is selected. If you want to listen to the sound from the TV speaker, set “Audio Out” to “TV+AMP” in the HDMI Settings menu.
Why does my Sony STR-DA2800ES Receiver turn on automatically?
If your Sony Receiver is turning on automatically, it might be due to the “Control for HDMI” being set to “On” or “Pass Through” being set to “Off.” In this case, the receiver may be turned on by operating other equipment connected to it.
What to do if the Universal Remote Control function does not work on my Sony Receiver?
Make sure the connections required are made. Press ?/1 on the remote control to turn the receiver off and then on again. Hold down ?/1 on the receiver until the lamp above the button flashes in green to reboot the receiver. If the remote sensor of the receiver and that of another Sony product face the same direction, interference may occur. In this case, set the remote sensors so that they face different directions or use an IR shield on the other Sony product to shield the IR from interference from the receiver IR remote.
How to resolve when a specific type of image is not output or corrupted on Sony STR-DA2800ES Receiver?
If a specific type of image is not output or is corrupted on your Sony Receiver, select the appropriate resolution on the receiver, as the resolution of output signals from the COMPONENT VIDEO OUT jacks may not be supported by your TV. The resolution of the signals output to the COMPONENT VIDEO MONITOR OUT jacks is converted up to 480p/576p because COMPONENT VIDEO MONITOR OUT jacks have restrictions on resolution when the resolution of video signals protected by copyright technology is converted.
What to do if when the Zone2 Out function is enabled and you select the same HDMI input for both the main zone and zone 2, there may be some interference on the audio with my Sony Receiver?
To avoid possible interference in the main zone, you can place priority on the main zone for HDMI input selection.
What to do if there is no sound from a specific device connected to my Sony Receiver?
If there is no sound from a specific device connected to your Sony Receiver, check that the device is connected correctly to the audio input jacks for that device. Verify that the cord(s) used for the connection is (are) fully inserted into the jacks on both the receiver and the device. Set the INPUT MODE to “AUTO”.
Why isn't the Control for HDMI function working on my Sony STR-DA2800ES?
If the Control for HDMI function does not work on your Sony Receiver, check the HDMI connection. Make sure “Control for HDMI” is set to “On” in the HDMI Settings menu. When “Zone2 Out” is set to “On,” the Control for HDMI function does not work.
What to do if the Pass Through function does not work on Sony STR-DA2800ES Receiver?
If the Pass Through function isn't working on your Sony Receiver, ensure that “HDMI A” is selected using the HDMI OUTPUT button, as “HDMI B” or “Off” will disable it. Also, if “Control for HDMI” is set to “On” and “Pass Through” is set to “Auto,” the receiver saves power in standby mode based on the TV's status. To enable power saving, the “Control for HDMI” on the TV should be effective; if not, set “Pass Through” on the receiver to “On.”
How to fix severe hum or noise on Sony STR-DA2800ES Receiver?
If you are experiencing severe hum or noise with your Sony Receiver, check that the speakers and equipment are connected correctly. Ensure connecting cords are away from transformers, motors, TVs, or fluorescent lights. Move your TV away from the audio equipment. If the plugs and jacks are dirty, wipe them with a cloth slightly moistened with alcohol.
Essential safety guidelines to prevent hazards like fire and electric shock.
Identification and function of the receiver's front panel components.
Details on digital, antenna, LAN, RS232C, and control jacks on the rear.
Identification and function of buttons on the RM-AAU155 remote control.
Essential steps and information before connecting any equipment to the receiver.
Explains different speaker setups like 7.1, 5.1 channels, and their configurations.
Detailed diagrams and instructions for connecting speaker wires to receiver terminals.
Steps and diagrams for connecting a TV using an HDMI cable.
How to connect devices with HDMI output jacks to the receiver's HDMI inputs.
Explanation of HDMI audio/video support, Control for HDMI, and high-resolution formats.
How to connect audio equipment with HDMI output jacks to the receiver.
How to properly connect the AC power cord to the receiver and wall outlet.
Using the on-screen Easy Setup for initial receiver configuration.
How to access and navigate the main home menu options.
Steps to select, play, and control audio/video content from connected devices.
Steps to connect a USB device and play back video, music, or photo files.
How to connect and control iPod/iPhone for music, video, and photo playback.
How to choose and apply different sound field modes for audio playback.
Specific sound fields optimized for movie playback like HD-D.C.S. and Dolby/DTS modes.
How to select and switch between different AV equipment for remote operation.
Explains enjoying audio/video in a zone other than the main zone.
Explanation of Sony's BRAVIA Sync feature and its reliance on HDMI CEC.
Procedure to clear all settings and reset the receiver to its original factory defaults.
Steps to enter and navigate the main settings menu on the TV screen.
Overview of settings related to initial setup and speaker configuration options.
Re-running the Easy Setup process for basic receiver configuration.
Using the Digital Cinema Auto Calibration for automatic speaker setup and matching.
Calibrating speaker phase characteristics for better surround sound imaging.
Manually adjusting the volume level for each individual speaker.
Converting analog video input signals to various resolutions for output.
Enabling HDMI control and signal pass-through functions.
Customizing input display names, icons, and visibility in menus.
Safety guidelines for handling objects, power sources, and heat buildup.
Solutions for automatic power changes, no picture/sound, and hot receiver issues.
General| Bi-amping | Yes |
|---|---|
| Night mode | No |
| Sample rate | 192 kHz |
| Product color | Black |
| Connector contacts plating | Nickel |
| Case or master carton weight | 15 kg |
| Power consumption (standby) | 0.5 W |
| Power consumption (typical) | 290 W |
| Dimensions (WxDxH) | 500 x 258 x 487 mm |
| Total Harmonic Distortion (THD) | 0.09 % |
Weight and Dimensions| Weight | 12400 g |
|---|
To Next Page
