What does it mean when the LAMP/COVER indicator flashes on my Sony Projector?
If the LAMP/COVER indicator is flashing on your Sony Projector, ensure that the lamp cover is securely attached. If it is already secured, the lens protector may have a problem. If it is necessary to use the projector in case of emergency, use it in the emergency mode.
What to do if my Sony VPL-DS100 says 'High temp.! Probably use in high altitude.'?
If your Sony Projector displays 'High temp.! Probably use in high altitude', and you are using it at an altitude of 1,500 m or higher, set the “High Altitude Mode” in the INSTALL SETTING menu to 'on'.
Why won't the power turn on for my Sony Projector?
If your Sony Projector won't turn on, it may be because the power was recently turned off and on with the I / 1 key at a short interval. Wait for about 90 seconds before attempting to turn it on again. Also, ensure that the lamp cover is securely closed.
What does it mean when the TEMP/FAN indicator lights up on my Sony VPL-DS100?
If the TEMP/FAN indicator lights up on your Sony Projector, it indicates that the internal temperature is unusually high. Check to see if anything is blocking the ventilation holes. Also, check to see whether or not the projector is being used at high altitudes.
What does it mean when the LAMP/COVER indicator lights up on my Sony VPL-DS100?
When the LAMP/COVER indicator lights up on your Sony Projector, it could mean that the lamp has reached the end of its life and needs to be replaced. Alternatively, the lamp may be overheating. In this case, wait for 90 seconds to allow the lamp to cool down before turning the power back on.
What to do if my Sony VPL-DS100 Projector says 'High temp.! Lamp off in 1 min.'?
If your Sony Projector displays the message 'High temp.! Lamp off in 1 min.', turn off the power immediately. Then, check the ventilation holes to ensure nothing is blocking them.
Why is my Sony VPL-DS100 not producing any sound?
If your Sony Projector isn't producing sound, first check that all cables are correctly connected. Ensure you are using a no-resistance stereo audio cable. Finally, verify that the sound settings on the projector are properly adjusted.
Why is there no picture on my Sony VPL-DS100?
There are several reasons why your Sony Projector might not be displaying a picture. Ensure the cables are properly connected. Select the correct input source using the INPUT key. Also, make sure your computer signal is set to output only to an external monitor. Depending on your computer, you may need to switch the output to the projector through specific keys or settings.
What to do if the image extends beyond the screen on my Sony Projector?
If the image extends beyond the screen on your Sony Projector, and there are black edges around the image, display the full image on the screen and press the APA key. You can also adjust “Shift” in the INPUT SETTING menu.
How to fix strange colors from INPUT A connector on my Sony VPL-DS100 Projector?
If the picture from the INPUT A connector on your Sony Projector appears to have strange colors, the “Input-A Signal Sel.” setting in the SET SETTING menu is incorrect. Select “Computer,” “Video GBR” or “Component” correctly according to the input signal.
Optical| projection system | 3 LCD panels, 1 lens projection system |
|---|---|
| panel | 0.62-inch TFT LCD 1, 440, 000 pixels (480, 000 pixels x 3) |
| projection lens | 1.2 times F2.2 to 2.4 f18.0 to 21.6mm |
| light output | 1200ANSI lm (lamp mode high) |
Screen Coverage| screen coverage | 40'' to 150'' (measured diagonally) |
|---|---|
| throwing distance 40-inch | 1.1 to 1.4 m (3.6 to 4.6 feet) |
| throwing distance 60-inch | 1.7 to 2.1 m (5.6 to 6.9 feet) |
| throwing distance 80-inch | 2.3 to 2.8 m (7.5 to 9.2 feet) |
| throwing distance 100-inch | 2.9 to 3.5 m (9.5 to 11.5 feet) |
| throwing distance 120-inch | 3.5 to 4.2 m (11.5 to 13.8 feet) |
| throwing distance 150-inch | 4.4 to 5.3 m (14.4 to 17.4 feet) |
Power| power requirements | AC 100 to 240 V, 50/60 Hz |
|---|---|
| power consumption max | 250 W |
| standby power consumption | 4.6 W |
Operating Environment| operating temperature | 0 to 35 degrees Celsius (32 to 95 F) |
|---|---|
| operating humidity | 35% to 85% (no condensation) |
| heat dissipation | 853.1BTU |
Input and Connectivity| input RGB/Component | Analog RGB (HD D-sub 15 pin x 1) |
|---|---|
| input S-Video | S-Video (Mini DIN 4pin x 1) |
| input composite | Composite video (RCA pin x 1) |
Weight and Dimensions| dimension (WxHxD) inch | 11 [5]/8 x 3 [1]/8 x 9 [3]/8 |
|---|---|
| dimension (WxHxD) mm | 295 x 78 x 238 |
| weight lb | Approx. 6 lbs., 3 oz. |
| weight kg | Approx. 2.8 kg |
To Next Page
