How to fix a Sony VPL-EW5 Projector that will not turn on?
If your Sony Projector isn't turning on, there could be a few reasons: * If the power has been rapidly turned off and on, wait about 90 seconds before attempting to turn it on again. * Ensure the lamp cover is securely closed. * Make sure the air filter cover is properly attached.
What does 'Please replace the Lamp and clean the Filter' mean on my Sony VPL-EW5 Projector?
This message indicates that it's time to replace the lamp and clean the air filter. Replace the lamp and clean the filter. When this message appears even after replacing the lamp, the task has not been completed. Perform the operation of steps 10 to 13 on page 43.
Why is the picture from the INPUT A connector colored strangely on my Sony VPL-EW5 Projector?
If the picture from the INPUT A connector is colored strangely on your Sony Projector, the input signal may not be received at “Auto” of “Input-A Signal Sel” on the SET SETTING menu, or the setting of “Input-A Signal Sel” may be incorrect. Select “Computer”, “Video GBR” or “Component” correctly according to the input signal.
How to stop the picture from flickering on my Sony Projector?
If the picture on your Sony Projector is flickering, “Dot Phase” on the INPUT SETTING menu may not be adjusted properly. Adjust “Dot Phase” on the INPUT SETTING menu properly.
How to troubleshoot a Sony VPL-EW5 Projector picture that is not clear?
If the picture on your Sony Projector is not clear: * The picture might be out of focus. Adjust the focus. * Condensation may have accumulated on the lens. Leave the projector for about two hours with the power on.
How to correct the color balance on a Sony Projector?
If the color balance is incorrect on your Sony Projector: * The picture might not have been adjusted properly. Adjust the picture. * The projector may be set to the wrong color system. Set “Color System” on the SET SETTING menu to match the color system being input.
How do I fix a Sony VPL-EW5 image that extends beyond the screen?
If the image extends beyond the screen on your Sony Projector, here's what you can do: * If the APA key has been pressed even though there are black edges around the image, display the full image on the screen and press the APA key. Adjust “Shift” on the INPUT SETTING menu properly. * If the input signal cannot be projected as the frequency is out of the acceptable range of the projector, input a signal that is within the range of the frequency. * If the resolution setting of the output signal of the computer is too high, set the output setting to SVGA (VPL-ES5), XGA (VPL-EX50/ EX5) or WXGA (VPL-EW5).
What to do if the picture is too dark on Sony VPL-EW5 Projector?
If the picture on your Sony Projector is too dark, consider the following: * The contrast or brightness may not be properly adjusted. Adjust these settings on the “Adjust Picture...” menu. * The lamp may have burnt out or is dim. If so, replace it with a new one.
What to do if Sony VPL-EW5 Projector flashes red 6 times?
If the '/1' indicator flashes red six times on your Sony Projector, unplug the AC power cord from the wall outlet after the '/1' indicator goes out. Then, plug the power cord back into the wall outlet and turn the projector on again. If the '/1' flashes in red and the problem persists, the electrical system has failed.
How to fix Sony VPL-EW5 Projector when the power is not turned on?
If the Sony Projector's power is not turning on, wait about 90 seconds before attempting to turn it on again, especially if it was recently turned off. Make sure that the lamp cover and the air filter cover are securely closed and attached.
Essential warnings regarding fire, electric shock, proper earthing, and handling.
Details on meeting FCC regulations for digital devices in the USA.
Advice on preventing heat buildup, cleaning procedures, and safe handling.
Guidance on unsuitable locations and ventilation requirements for installation.
Specific conditions to avoid, such as tilt or upright positioning, to prevent malfunction.
Notes on high altitude usage, carrying, screen interaction, and security bar use.
Tables showing recommended distances for various screen sizes and projector models.
Step-by-step guide on how to safely replace the projector's lamp.
Instructions for cleaning the air filter to maintain optimal performance.
Solutions for problems like no power, no picture, or incorrect colors.
Addresses issues with no sound, flickering pictures, and indicator light patterns.
Explains common warning messages and their remedies, including indicator light errors.
General| Dimensions | 365 x 96.2 x 252 mm |
|---|---|
| Display Type | 3LCD |
| Projection Size | 30" to 300" |
| Lamp Life (Normal mode) | 4000 hours |
| Resolution | 1280x800 (WXGA) |
| Lamp Type | UHP |
| Input Ports | HDMI, VGA, S-Video, Composite |
| Lamp Life | 4000 hours (Normal mode), 5000 hours (Eco mode) |
To Next Page
