To Next PageTo Next PageWhat does it mean when LAMP/COVER flashes red on Sony VPL-HW55ES Projector (3 flashes)?
If the LAMP/COVER indicator on your Sony Projector flashes red with a repetition rate of 3 flashes, the lamp has reached the end of its lifespan and needs to be replaced. Alternatively, the lamp may have reached a high temperature; wait for it to cool down before turning the power back on.
What does it mean when ON/STANDBY flashes red on Sony VPL-HW55ES Projector (4 flashes)?
If the ON/STANDBY indicator on your Sony Projector flashes red with a repetition rate of 4 flashes, it indicates a broken fan. Consult with qualified Sony personnel.
Why is the picture too dark on my Sony VPL-HW55ES Projector?
If the picture on your Sony Projector is too dark, adjust the “Contrast” or “Brightness” in the Picture menu.
How to fix Sony VPL-HW55ES power not turning on?
If your Sony Projector's power is not turning on, ensure that the lamp cover and filter holder are securely closed and tightened. After about 1 minute, attempt to turn the power on. Also, check the warning indicators.
Why does the power suddenly turn off on my Sony VPL-HW55ES?
If your Sony Projector's power suddenly turns off, check that “Power Saving” in the Setup menu is set to “Standby.” If it is, set “Power Saving” to “Off.”
What to do if my Sony VPL-HW55ES power is not turned on?
If your Sony Projector doesn't turn on, it might be because you recently turned it off and are trying to turn it back on too quickly. Wait about 1 minute before trying again. Also, ensure the lamp cover and the filter holder are securely closed and tightened. Finally, check the warning indicators.
Why does my Sony Projector keep turning off suddenly?
Your Sony Projector might be turning off suddenly because the “Power Saving” setting in the Setup menu is set to “Standby.” You can resolve this by setting “Power Saving” to “Off.”
What does it mean when LAMP/COVER flashes red on Sony Projector?
If the LAMP/COVER indicator on your Sony Projector flashes red with a repetition rate of 2 flashes, it indicates that the lamp cover or filter holder is not securely closed. Make sure to close the lamp cover and filter holder securely, then tighten the screws.
Why does my Sony Projector's video image not seem like 3D?
If the video image on your Sony Projector doesn't seem like 3D, first check that your 3D glasses are turned on and charged. Ensure the input source is HDMI and that “2D-3D Display Sel.” is set to “Auto” or “3D”. Verify that the input signals are compatible 3D signals. If connected to 3D equipment, restarting the equipment may help. If using a 3D Sync Transmitter, ensure it is within the specified range. Adjust the zooming magnification to low, or move farther from the screen if the screen size is inappropriate.
How to fix a blurry picture on Sony VPL-HW55ES?
If the picture from your Sony Projector is not clear, try adjusting the focus. If condensation has accumulated on the lens, leave the projector on for about 2 hours to allow it to clear.
General| Display Technology | SXRD |
|---|---|
| Resolution | 1920 x 1080 |
| Brightness | 1700 ANSI lumens |
| Contrast Ratio | 120, 000:1 |
| Lamp Life | 6000 hours |
| Zoom Ratio | 1.6x |
| Lens Shift | Vertical: ±71%, Horizontal: ±25% |
| 3D | Yes |
| Projection Size | 40 to 300 inches |
| Dimensions | 407.4 x 179.2 x 463.9 mm |
| Inputs | 2 x HDMI, 1 x Component, 1 x Composite |
| Throw Ratio | 1.36 - 2.16:1 |
