EasyManua.ls Logo

spherag ATLAS 2 - User Manual

spherag ATLAS 2
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
EN
G ET IT O N
IRRIGATION CONTROLLER WITH A
SELF-SUFFICIENT SOLAR CELL
USER
MANUAL

Table of Contents

Other manuals for spherag ATLAS 2

Preview: Quick Start Guide
Quick Start Guide2 pages

Questions and Answers

  • D
    diananelsonAug 8, 2025
    Why is irrigation not carried out with spherag Controller?
    • R
      Ronald ClementsAug 8, 2025
      Irrigation might not occur due to several reasons. One cause could be driver failure from bypassing the red and black wires during an open or close command. In this case, send the device to its supplier or directly to Spherag’s facilities for analysis. If the failure is due to manufacturing defects, it will be repaired. However, if it results from a short-circuit, the failure is irreparable, and SPHERAG assumes no liability. Another reason may be an empty battery; ensure you follow the installation guidelines (Step 5). Also, the program might not be received on the device due to poor signal quality, so placing it in a higher location could improve signal reception.
  • D
    Dr. Austin GomezAug 12, 2025
    What to do if spherag Controller battery does not charge?
    • E
      ebrooksAug 12, 2025
      If your spherag Controller battery isn't charging, it could be due to incorrect installation. Ensure you follow the installation guidelines. Another cause might be a lack of sunny days, especially in winter. To address this, turn the device to ECO mode, or to PSM mode if it is not irrigation time.
  • K
    Kimberly MccartyAug 17, 2025
    What to do if water flow does not get interrupted with spherag ATLAS 2?
    • F
      frank73Aug 17, 2025
      If the water flow doesn't stop when it should with your spherag Controller, it may be due to an improperly installed valve. Ensure that the valve is installed with the arrow pointing in the direction of the water flow. Another potential cause is a damaged solenoid, which would require replacement.
  • M
    Melissa SanchezAug 21, 2025
    Why is spherag ATLAS 2 LED not shining?
    • J
      jacob96Aug 21, 2025
      If the LED on your spherag Controller isn't shining, it's likely due to an empty battery. Please refer to the installation guidelines, specifically Step 5, to address this issue.
  • J
    jenniferwrightAug 25, 2025
    What to do if solenoid state on spherag ATLAS 2 Controller does not match platform display?
    • W
      William ToddAug 26, 2025
      If the solenoid's state on your spherag Controller doesn't match what's displayed on the platform, it could be because synchronization hasn't been carried out. Try performing a synchronization. Alternatively, the solenoid's polarity might not be correctly connected to the ATLAS output; in this case, change the polarity.
  • H
    Heather MorganAug 29, 2025
    Why spherag Controller has false readings of flow rate?
    • A
      Ashley CrawfordAug 29, 2025
      False flow rate readings with the spherag Controller may occur if the wires (white and blue) are not electrically insulated. Ensure that these wires are insulated with non-conductive materials.
  • P
    Priscilla OrtegaSep 3, 2025
    Why there is no water flow in spherag Controller?
    • D
      Danielle ValenzuelaSep 3, 2025
      The absence of water flow in your spherag Controller could be due to a valve blocked by dirt or fouling. In this case, replace the valve.

spherag ATLAS 2 Specifications

General IconGeneral
CompatibilityPC, PlayStation
ConnectionUSB-C
BatteryLithium-ion
Buttons2 analog sticks, D-pad
RGB LightingCustomizable RGB
Additional FeaturesProgrammable buttons