Spring Air Systems HT-B - SBA10 C;SBA10 H One Sequence Wash with Time Clock Electrical; AP10 C;AP10 H One Sequence Wash with Time Clock Electrical

_____________________________________________________________________________________________
Spring Air Systems Water Wash Ventilator Maintenance Manual 11/01
27
SBA10C & SBA10H single sequence electrical wiring
Figure 34
AP10C & AP10H single sequence electrical wiring
Figure 35
NOTE 1:
ALL REMOTE ELECTRIAL WIRING
AND NATIONAL CODE REQUIREMENTS
SHALL CONFORM TO ALL LOCAL
INTERNAL WIRING BY SPRING AIR
Q: 1 2 3 4 RUN
Mo 09:00
I: 1 2 3 4 5 6
SMART RELAY
Q1
L
Q2
NI1I2
FAN SWITCH
OFF/AUTO/ON
PUMP
DETERGENT
HOT WATER SOLENOID
WASH PILOT
H
B
FAN PILOT
OPTIONAL COLD
WATER SOLENOID
C
G
ESC
Q3
OK
Q4
I3 I4 I5 I6
CURCUIT BREAKER
4
4
8
9
3
5
1
END SWITCH
TWO (2) WIRES TO THE
MOTOR STARTERS OVERLOADS
5
1
RED
WHITE
WET CHEMICAL CONTROL
HEAD 120V/1/60 - 1A.
ELECTRICAL DIVISION
AND DISCONNECTS BY
NOTE 2:
SHUTOFF DAMPER AND END SWITCH 120V/1/60
(OPTIONAL) THREE (3) WIRES TO SUPPLY AIR MOTORIZED
MOTOR STARTER - 120V/1/60 - 2 AMPS MAXIMUM
(OPTIONAL) POWER SUPPLY TO SUPPLY FAN
LV10 PANEL - 120V/1/60 - 2 AMPS MAXIMUM.
POWER TO THE SPRING AIR SYSTEMS ENVIRO FILTER UNIT
POWER TO THE EXHAUST FAN MOTOR STARTER
24 HOURS/DAY - 120V/1/60 - 15 AMPS
POWER SUPPLY TO THE SB10H/C PANEL
NORMALLY OPEN
2 AMPS MAXIMUM.
9
4
8
9
4
REMOTE WIRING BY TRADES
120V/1/60 - 2 AMPS MAXIMUM.
3
4
4
1
OR
x
x
o
x
ox
o
ox
H
C
HOT WATER SOLENOID
DETERGENT
WASH PILOT
B
PUMP
WATER SOLENOID
OPTIONAL COLD
FAN PILOT
G
1
5
INTERNAL WIRING BY SPRING AIR
FIRE TEST
PUMP TEST
I3
FAN SWITCH
Q: 1 2 3 4 RUN
Mo 09:00
I: 1 2 3 4 5 6
SMART RELAY
Q1 Q2
NLI1I2
OFF/AUTO/ON
10
ESC OK
Q3 Q4
I4 I5 I6
9
8
4
4
10
4
9
8
4
9
3
4
5
2
1
1
4
4
3
4
1
CURCUIT BREAKER
120V/1/60 - 3 AMPS - WIRE EACH SOE IN PARALLEL.
THREE (3) WIRES TO EACH SOE ENCLOSURE LOCATED
120V/1/60 - 1 AMPS. WIRE EACH ENS IN PARALLEL.
ONLY. ARRANGEMENT "D" FIRE DAMPER HOODS REQUIRES NO REMOTE WIRING.
AT EACH EXHAUST DUCT COLLAR ON EVERY HOOD
AT EACH EXHAUST DUCT COLLAR ON EVERY HOOD
TWO (2) WIRES TO EACH ENS ENCLOSURE LOCATED
4
REMOTE WIRING FOR ARRANGEMENT "F" & "T" TYPE FIRE DAMPER HOODS
ARRANGEMENT "T" FIRE DAMPER:
ARRANGEMENT "F" FIRE DAMPERS:
TWO (2) WIRES TO THE
WET CHEMICAL CONTROL
HEAD 120V/1/60 - 1A.
DAMPER END SWITCH
DAMPER SOLENOID
FENWALL DETECTOR
2
1
2
1
END SWITCH
NORMALLY OPEN
RED
WHITE
OR
RELAY SUPPLIED AND INSTALLED BY ELECTRICAL DIVISION)
120V/1/60 - 2 AMPS MAXIMUM. (SHUNT TRIP OR
COOKING EQUIPMENT IN THE EVENT OF A FIRE
POWER TO SHUNT TRIP TO DE-ACTIVATE ELECTRIC
SHUTOFF DAMPER AND END SWITCH 120V/1/60
(OPTIONAL) THREE (3) WIRES TO SUPPLY AIR MOTORIZED
MOTOR STARTER - 120V/1/60 - 2 AMPS MAXIMUM
(OPTIONAL) POWER SUPPLY TO SUPPLY FAN
LV10 PANEL - 120V/1/60 - 2 AMPS MAXIMUM.
POWER TO THE SPRING AIR SYSTEMS ENVIRO FILTER UNIT
POWER TO THE EXHAUST FAN MOTOR STARTER
24 HOURS/DAY - 120V/1/60 - 15 AMPS
POWER SUPPLY TO THE AP10H/C PANEL
2 AMPS MAXIMUM.
120V/1/60 - 2 AMPS MAXIMUM.
OR
REMOTE WIRING BY TRADES
x
x
o
x
ox
o
ox