SRAM Quarq User Manual

29
7. Align the dot on the outer ring of the
battery cap with the recessed dot on the
inner ring of the SLED. While pressing the
end of the SLED into the spindle with your
thumb, use your fingers, or a spanner
wrench if necessary, to turn the battery
cap counter-clockwise 90 degrees, in the
direction of the arrow, until the dot on the
outer ring is aligned with the raised dot
on the inner ring.
7. Align the dot on the outer ring of the
battery cap with the recessed dot on the
inner ring of the SLED. While pressing the
end of the SLED into the spindle with your
thumb, use your fingers, or a spanner
wrench if necessary, to turn the battery
cap counter-clockwise 90 degrees, in the
direction of the arrow, until the dot on the
outer ring is aligned with the raised dot
on the inner ring.
7. Align the dot on the outer ring of the
battery cap with the recessed dot on the
inner ring of the SLED. While pressing the
end of the SLED into the spindle with your
thumb, use your fingers, or a spanner
wrench if necessary, to turn the battery
cap counter-clockwise 90 degrees, in the
direction of the arrow, until the dot on the
outer ring is aligned with the raised dot
on the inner ring.
7. Align the dot on the outer ring of the
battery cap with the recessed dot on the
inner ring of the SLED. While pressing the
end of the SLED into the spindle with your
thumb, use your fingers, or a spanner
wrench if necessary, to turn the battery
cap counter-clockwise 90 degrees, in the
direction of the arrow, until the dot on the
outer ring is aligned with the raised dot
on the inner ring.
7. Align the dot on the outer ring of the
battery cap with the recessed dot on the
inner ring of the SLED. While pressing the
end of the SLED into the spindle with your
thumb, use your fingers, or a spanner
wrench if necessary, to turn the battery
cap counter-clockwise 90 degrees, in the
direction of the arrow, until the dot on the
outer ring is aligned with the raised dot
on the inner ring.
7. Align the dot on the outer ring of the
battery cap with the recessed dot on the
inner ring of the SLED. While pressing the
end of the SLED into the spindle with your
thumb, use your fingers, or a spanner
wrench if necessary, to turn the battery
cap counter-clockwise 90 degrees, in the
direction of the arrow, until the dot on the
outer ring is aligned with the raised dot
on the inner ring.
7. Align the dot on the outer ring of the
battery cap with the recessed dot on the
inner ring of the SLED. While pressing the
end of the SLED into the spindle with your
thumb, use your fingers, or a spanner
wrench if necessary, to turn the battery
cap counter-clockwise 90 degrees, in the
direction of the arrow, until the dot on the
outer ring is aligned with the raised dot
on the inner ring.
7. Align the dot on the outer ring of the
battery cap with the recessed dot on the
inner ring of the SLED. While pressing the
end of the SLED into the spindle with your
thumb, use your fingers, or a spanner
wrench if necessary, to turn the battery
cap counter-clockwise 90 degrees, in the
direction of the arrow, until the dot on the
outer ring is aligned with the raised dot
on the inner ring.
7. Align the dot on the outer ring of the
battery cap with the recessed dot on the
inner ring of the SLED. While pressing the
end of the SLED into the spindle with your
thumb, use your fingers, or a spanner
wrench if necessary, to turn the battery
cap counter-clockwise 90 degrees, in the
direction of the arrow, until the dot on the
outer ring is aligned with the raised dot
on the inner ring.
Adjust Régler Ajustar
Einstellen Regolare
調節
Ajustar Afstellen
󸛩󷐽
7

SRAM Quarq Specifications

General

Type	Power Meter
Wireless Protocol	ANT+, Bluetooth
Accuracy	+/- 1.5%
Battery Type	CR2032
Battery Life	200 hours
Water Resistance	IPX7