STACYC Stability Cycle - Troubleshooting Guide

P a g e | 20P a g e | 20 DOC 001 REV A DOC 001 REV A P a g e | 21
Replace Chain:
Note: Chain may be greasy and dirty.
Turn power switch to “OFF” posion, remove baery, allow STACYC Stability Cycle
to cool before beginning repair or maintenance:
1. Ensure the power switch is “OFF”.
2. Ensure the baery is removed and STACYC stability cycle has had adequate me
to cool. (up to 30 minutes)
3. Secure the STACYC stability cycle for repair or maintenance.
4. Exercise cauon around exposed parts.
5. Remove foot rest.
6. Remove right side panel.
7. Rotate rear wheel unl master chain link is near motor sprocket.
8. Loosen both rear axle nuts, bolt securing brake hub and loosen chain tensioner.
9. Push wheel forward to loosen chain.
10. Remove master chain link, then chain.
11. Install replacement chain, re-aach master link.
12. Tension chain by pulling rear wheel outward with aid of chain tensioner, aligning
the re straight forward.
13. Tighten rear axle nuts, bolt securing brake hub and snug chain tensioner.
14. Install right side panel.
Replace Front Tire and/or Tube:
1. Loosen front axle nuts and axle keeper tabs.
2. Remove wheel.
3. Deate tube and remove re from wheel.
4. UN-Install new re and/or tube onto sidewall.
5. Inate to pressure recommended on sidewall.
6. Install front wheel and ghten from axle nuts, posioning axle keeper tabs into lower hole
in fork blade.
Replace Rear Tire and/or Tube:
1. Remove foot rest.
Chain Tensioner Bolt to secure brake hub
◀
◀
2. Remove right side panel.
3. Loosen rear anchor bolt of brake assembly to release brake cable.
4. Remove brake assembly mount bolt.
5. Loosen rear axle nuts and remove chain tensioner assembly.
6. Push rear wheel forward and remove chain from motor sprocket.
7. Remove rear wheel.
8. Deate tube and remove re from wheel.
9. Install new re and/or tube onto wheel.
10. Inate to pressure recommended on sidewall.
11. Tension chain by pulling rear wheel outward with aid of chain tensioner, aligning the re
straight forward.
12. Tighten rear axle nuts, bolt securing brake hub and snug chain tensioner.
13. Tighten rear anchor bolt of brake assembly to capture brake cable.
14. Install right side panel.
Baery: Refer to baery manufacturer documentaon for proper baery maintenance.
Baery Disposal: Your STACYC product uses sealed lithium cell baeries which must be recycled
or disposed of in an environmentally safe manner. Do not dispose of a lithium cell baery in
a re; the baery may explode or leak. Do not dispose of a lithium cell baery in your regular
household trash. The incineraon, land lling or mixing of sealed lithium cell baeries with
household trash is prohibited by law in most areas. Return exhausted baeries to a federal or
state approved lithium cell baery recyclers or a local seller of baeries. Many states have
laws prohibing the disposal of lithium cell baeries in the municipal waste stream. Check
with your local state law.
Wheels/Tires:
Wheels and res are subject to normal wear and tear. It is the responsibility of the user and
parent to periodically inspect wheels and res for damage and excessive tread wear.
TROUBLESHOOTING GUIDE
A fully charged baery must be installed prior to performing any troubleshoong and must
ONLY be performed by an adult.
PROBLEM:
POSSIBLE CAUSE:
SOLUTION:
Power Switch
is turned “ON”,
STACYC does not
work
Baery not installed or fully seated
Verify a fully charged baery is installed
unl baery release buon “clicks”
Verify the baery is fully charged
Verify the fuse is good and properly
installed. Look for water damage. Replace
the fuse with the correct amperage fuse
Baery not fully charged
Fuse not installed or burnt-out