Why indicator does not light when charging a battery of Standard Horizon Transceiver?
If the indicator light does not illuminate when charging the battery of your Standard Horizon Transceiver, it could indicate a defective FNB-V99LI battery.
What to do if Standard Horizon Transceiver can not fix the GPS satellites?
If your Standard Horizon Transceiver can't fix the GPS satellites, it might be due to a couple of reasons. First, ensure that the internal GPS receiver is turned on. If it is already on, try moving to a location with fewer obstructions, as the current position may have poor GPS satellite reception.
What to do if Standard Horizon Transceiver cannot receive the DSC call?
If you cannot receive a DSC call on your Standard Horizon Transceiver, there are a couple of things to check. First, make sure the squelch is not open. Press the [SQL] key and then the [S] key until the “ ” icon disappears. Also, verify that DSC SCAN is turned “on” in the DSC Setup menu.
Why does Standard Horizon HX850S Transceiver [SCAN(DW)] key not start the scan?
If the [SCAN(DW)] key on your Standard Horizon Transceiver isn't starting the scan, it could be due to two reasons: either no channels are memorized, or the squelch is not adjusted correctly. To resolve this, first use the [MEM] key to enter desired channels into the transceiver’s memory. If that doesn't work, press the [SQL] key and press the [S] key until the “ ” icon disappears. Further adjustment of the squelch control may eliminate incoming signals.
What to do if Standard Horizon HX850S Transceiver press and holding the [SQL] switch does not eliminate background noise?
If pressing and holding the [SQL] switch on your Standard Horizon Transceiver isn't eliminating background noise, it could be due to low battery or a low audio volume level. Try charging the battery first. If the issue persists, press the [VOL] key and then press the [S] key several times to increase the audio volume.
What to do if Standard Horizon Transceiver cannot change any function?
If you cannot change any function on your Standard Horizon Transceiver, the Key Lock might be turned “on”. Ensure the Key Lock is turned “off”.
Why Standard Horizon Transceiver USA/INTL/CAN modes do not function?
If the USA/INTL/CAN modes on your Standard Horizon Transceiver are not functioning, ensure you are following the correct procedure: HOLD down the [16/9] key and press the [WX] key.
What to do if Standard Horizon Transceiver Key Lock does not function?
If the Key Lock on your Standard Horizon Transceiver is not functioning, make sure you are holding down the [H/L( )] key for 2 seconds.
Why Standard Horizon HX850S Transceiver cannot transmit the DSC?
If your Standard Horizon Transceiver cannot transmit the DSC, it is likely because the MMSI number has not been programmed yet.
General| Type | Handheld VHF Marine Transceiver |
|---|---|
| Waterproof Rating | IPX8 |
| GPS | Yes |
| DSC | Yes |
| Floatation | Yes |
| Channels | All USA, International and Canadian channels |
| Output Power | 6W |
| Battery | Lithium-ion battery |
| Display | Full dot matrix LCD |
| Battery Type | Lithium Ion |
| Dimensions | 2.6" x 5.3" x 1.5" (66 x 135 x 38mm) |
Guidelines for safe RF exposure from the transceiver, including separation distances.
Details on maritime station licenses, call signs, and Canadian licensing.
Information regarding FCC compliance, device limitations, and interference correction measures.
Overview of the HX850S, its features like channels, scanning, and DSC capabilities.
Lists items included in the packing list and available optional accessories for the HX850S.
Explanation of VHF marine band frequencies, transmission range factors, and usage restrictions.
Covers battery safety, installation, removal, life, charging, and charger cradle usage.
Instructions for connecting a chart plotter to the CD-38 cradle for NMEA data.
Details on the ANT Jack and MIC/SP Jack for antenna and accessories.
Explains the PTT switch, DISTRESS key, and essential keypad functions like VOL, SQL, and WX.
Describes keypad functions for scanning, power control, channel selection, and keypad locking.
Details the CALL/ENT/MENU key, TX/BUSY indicator, microphone, speaker, NMEA terminals, and battery lock.
Lists prohibited transmissions and steps for initial radio setup and reception.
Covers transmitting, power levels, and displaying GPS receiving data.
Guidance on using USA, Canadian, International channels, and simplex/duplex modes.
Instructions for accessing NOAA weather broadcasts and setting up weather alerts.
Details on selecting scan types (Memory, Priority) and operation.
Explains Dual Watch functionality and emergency procedures on Channel 16.
Covers operating on channels 13/67 and enabling the SOS strobe feature.
Introduction to DSC, its purpose, and the importance of the MMSI number.
Steps for programming the MMSI number into the HX850S.
Procedures for transmitting and receiving DSC distress alerts, including nature of distress.
How to transmit and receive All Ships calls for Urgency and Safety.
Setting up the individual directory, replies, and transmitting/receiving individual calls.
Features for enabling, reviewing, and deleting calls from the Call Waiting Directory.
Setting up, transmitting, and receiving group calls for coordinated communication.
Managing position requests and reports, including setup and transmission.
Customizing display modes like Radio, Position, Navigation, and GPS Status.
Adjusting display dimmer levels and contrast for optimal readability.
Configuring display/keypad illumination time and setting the priority channel for scanning.
Selecting scan modes (Memory/Priority) and defining scan resume behavior.
Adjusting key beep loudness and configuring NOAA weather alert reception.
Customizing channel names and configuring TX/BUSY LED modes.
Turning the internal GPS unit on/off and selecting power saving levels.
Configuring coordinate display format and time offset from UTC.
Setting the time display to local or UTC, and choosing 12/24 hour format.
Selecting units for Speed Over Ground and prioritizing GPS data sources.
Configuring NMEA output sentences and selecting units for altitude measurement.
General maintenance tips for preventing damage and information on ordering replacement parts.
Procedures for factory service and a chart for diagnosing and resolving common issues.
Explanation of channel assignments, usage conventions, and chart data.
Details of the limited warranty, coverage periods, and online registration process.
Instructions for installing the optional FBA-38 alkaline battery case.
Nominal performance specifications for frequency, power, sensitivity, and GPS.
To Next Page