Why Stanley Nail Gun fails to operate?
The Stanley Nail Gun might fail to operate due to several reasons: the On/Off Valve is in the ‘OFF’ position (set it to ‘ON’); there's insufficient air pressure (adjust it to the specified level); or the Trigger Valve is damaged (it needs replacement).
What to do if Stanley Nail Gun does not return fully?
If your Stanley Nail Gun isn't fully returning, it could be due to an air leak (tighten joints or replace components), low air pressure (adjust to the correct level), a build-up of debris inside the Nose Equipment (service and clean it), or the Stem Collector not being fully attached (check the Collector Bottle).
Why Stanley Nail Gun needs more than one trigger operation to place rivet?
If your Stanley Nail Gun requires multiple trigger pulls to place a rivet, the issue might stem from an air leak (tighten joints or replace components), low air pressure (adjust to specification), worn or broken Jaws (fit new Jaws), low oil level or air in the oil (prime the tool), a build-up of debris inside the Nose Equipment (clean the Nose Assembly), or an improperly attached Collector Bottle (check the Collector Bottle).
What to do if Stanley Nail Gun rivet stem does not break?
If the rivet stem isn't breaking on your Stanley Nail Gun, check for these potential causes: low air pressure (adjust to the correct specification), using a fastener outside the tool's capability (refer to the Placing Tool Rivet Range & Nose Equipment table), incorrect Nose Equipment for the rivet (refer to ProSet Nose Equipment Manual 07900-09412 to select and install the correct nose equipment), or low oil level/air in the oil (prime the tool).
What to do if Stanley Nail Gun will not grip stem of rivet?
If your Stanley Nail Gun won't grip the rivet stem, consider these possibilities: worn or broken Jaws (fit new Jaws), broken rivet stems jammed in the Nose Equipment (clean the Nose Assembly), a loose Jaw Guide (tighten it against the Pulling Head), a weak or broken Spring (fit a new spring), or using an incorrect Nose Piece or Nose Equipment for the rivet (refer to the ProSet Nose Equipment Manual 07900-09412 to select and install the correct one).
Why Stanley Nail Gun jaws will not release broken stem of rivet?
If the jaws of your Stanley Nail Gun won't release the broken rivet stem, it could be due to debris inside the Nose Equipment (clean the Nose Assembly), the Jaw Guide, Nose Piece, or Nose Housing not seated correctly (assemble the affected parts correctly), a weak or broken Spring (fit a new spring), or excess hydraulic oil or air in the oil (prime the tool).
Why Stanley Nail Gun has low vacuum?
A low vacuum in your Stanley Nail Gun can be caused by: the Stem Collector being removed or not fully attached (check the Stem Collector), the Stem Collector being full of stems (empty the Stem Collector), or low air pressure (adjust air pressure to within specification).
Why Stanley Nail Gun has slow cycle?
A slow cycle in your Stanley Nail Gun may be due to low air pressure (adjust to the specified level), a build-up of debris inside the Nose Equipment (service and clean the Nose Assembly), or the Collector Bottle being removed or not fully attached (check the Collector Bottle).
What to do if cannot insert rivet into Stanley Nail Gun?
If you cannot insert a rivet into your Stanley Nail Gun, the potential causes are: using an incorrect Nose Piece for the rivet (refer to the ProSet Nose Equipment Manual 07900-09412 to select and install the correct nose piece), broken rivet stems jammed in the Nose Equipment (refer to ProSet Nose Equipment Manual 07900-09412 and check Nose Equipment is correct for rivet), broken rivet stems jammed in the Hydraulic Piston (empty the Collector Bottle), or debris in the Nose Piece (service and clean the Nose Assembly).
What to do if my Stanley Power Tool fails to operate?
If your Stanley Power Tool isn't working, there are a few things to check: First, make sure the On/Off Valve (7) is in the ‘ON’ position. Next, ensure that the air pressure is within the specified range. Finally, if neither of those solutions works, the Trigger Valve (45) may be damaged and require replacement.
General| Brand | Stanley |
|---|---|
| Model | 76001 |
| Category | Power Tool |
| Language | English |
To Next Page
