10
The safety tag (p/n
15875) at right is attached
to the tool when shipped
from the factory. Read
and understand the safety
instructions listed on this
tag before removal. We
suggest you retain this tag
and attach it to the tool
when not in use.
TOOL STICKERS & TAGS
(shown smaller then actual size)
SAFETY TAG P/N 15875
IMPORTANT
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
1. FAILURE TO USE HYDRAULIC HOSE LABELED
AND CERTIFIED AS NON-CONDUCTIVE WHEN
USING HYDRAULIC TOOLS ON OR NEAR
ELECTRICAL LINES MAY RESULT IN DEATH
OR SERIOUS INJURY.
BEFORE USING HOSE LABELED AND CERTI-
FIED AS NON-CONDUCTIVE ON OR NEAR
ELECTRIC LINES BE SURE THE HOSE IS
MAINTAINED AS NON-CONDUCTIVE. THE
HOSE SHOULD BE REGULARLY TESTED FOR
ELECTRIC CURRENT LEAKAGE IN ACCOR-
DANCE WITH YOUR SAFETY DEPARTMENT
INSTRUCTIONS.
2. A HYDRAULIC LEAK OR BURST MAY CAUSE
OIL INJECTION I N T O T H E
BODY OR CAUSE OTHER SEVERE PERSONAL
INJURY.
A DO NOT EXCEED SPECIFIED FLOW AND
PRESSURE FOR
IMPORTANT
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
D DO NOT LIFT OR CARRY TOOL BY THE
HOSES. DO NOT ABUSE HOSE. DO NOT
USE KINKED, TORN OR DAMAGED HOSE.
3. MAKE SURE HYDRAULIC HOSES ARE PROP-
ERLY CONNECTED TO THE TOOL BEFORE
PRESSURING SYSTEM. SYSTEM PRESSURE
HOSE MUST ALWAYS BE CONNECTED TO TOOL
“IN” PORT. SYSTEM RETURN HOSE MUST
ALWAYS BE CONNECTED TO TOOL “OUT” PORT.
REVERSING CONNECTIONS MAY CAUSE RE-
VERSE TOOL OPERATION WHICH CAN RESULT
IN SEVERE PERSONAL INJURY.
4. DO NOT CONNECT OPEN-CENTER TOOLS TO
CLOSED-CENTER HYDRAULIC SYSTEMS. THIS
MAY RESULT IN LOSS OF OTHER HYDRAULIC
FUNCTIONS POWERED BY THE SAME SYSTEM
AND/OR SEVERE PERSONAL INJURY.
5. BYSTANDERS MAY BE INJURED IN YOUR WORK
AREA. KEEP BYSTANDERS CLEAR OF YOUR
WORK AREA.
DANGER
DANGER
28323
CE Decal
28409
Composite Decal
11207
Circuit Type D Decal
Failure to use hydraulic hose labeled and certified
Failure to use hydraulic hose labeled and certified
as non-conductive when using hydraulic tools on
as non-conductive when using hydraulic tools on
or near electric lines may result in death or
or near electric lines may result in death or
For proper and safe operation read owners manual
For proper and safe operation read owners manual
and mwke sure that you have been properly
and mwke sure that you have been properly
trained in correct procedures required for work
trained in correct procedures required for work
serious injury.
on or around electric lines.
on or around electric lines.
ELECTROCUTION
HAZARD
DANGER
12412
Electrical Warning Decal
05153
Stanley Decal
03786
7-9 GPM Decal
34685
Sound Power Decal
03782
4-6 GPM Decal
THIS CHAIN SAW IS
EQUIPPED WITH AN
AUTOMATIC CHAIN
OILER.
SEE YOUR PARTS &
SERVICE BOOK FOR
PROPER ADJUSTING
PROCEDURES
04746
Automatic Oiler
Decal
15863
Danger Decal
65839 - CS25 (shown)
65840 - CS28
Name Tag
11206
Circuit Type C Decal
03693
Closed Center Decal
To Next Page
Loading...