EasyManua.ls Logo

Stanley SCD20C2 - User Manual

Stanley SCD20C2
27 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Taladro/Atornillador Inalámbrico de Ión de Litio
Parafusadeira/Furadeira a Bateria de Íon de Lítio
Lithium-Ion Cordless Drill Driver
SCD20
SCD20C2
SCD20C2K
SCD201C2K
MANUAL DE INSTRUCCIONES
MANUAL DE INSTRUÇÕES
INSTRUCTIONS MANUAL
ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
ADVERTÊNCIA: LEIA ESTAS INSTRUÇÕES ANTES DE USAR O PRODUTO.
WARNING: READ INSTRUCTIONS MANUAL BEFORE USING PRODUCT.
Español 4
Português 12
English 20

Table of Contents

Questions and Answers

  • M
    mdunlapAug 7, 2025
    Why won't my Stanley Drill battery pack charge?
    • J
      Joy Thomas MDAug 7, 2025
      If your Stanley Drill battery pack won't charge, there are a few possible reasons: * The battery pack might not be inserted into the charger. Insert the battery pack into the charger until the LED lights. * The charger might not be plugged in. Plug the charger into a working outlet. * The surrounding air temperature might be too hot or too cold. Move the charger and battery pack to a surrounding air temperature of above 40°F (4,5°C) or below 105°F +40,5°C).
  • K
    Kristin CohenAug 12, 2025
    What to do if Stanley SCD20C2 Drill starts immediately when inserting battery?
    • D
      Dustin Jackson MDAug 12, 2025
      If your Stanley Drill starts immediately upon inserting the battery, the switch has likely been left in the “On” position. The switch must be moved to “Off” to prevent the tool from immediately starting when the battery is inserted.
  • C
    Christopher PetersonAug 16, 2025
    How to fix Stanley SCD20C2 Drill battery pack will not charge?
    • C
      Crystal NavarroAug 16, 2025
      If the battery pack for your Stanley Drill won't charge, there are a few things to check: 1. Make sure the battery pack is fully inserted into the charger until the LED lights come on. 2. Verify that the charger is plugged into a working outlet. 3. Ensure the surrounding air temperature is suitable, above 40 degrees F (4.5ºC) and below 105 degrees F (+40.5ºC). Move the charger and battery pack if necessary.
  • K
    Kevin WigginsAug 20, 2025
    Why does my Stanley Drill shut off abruptly?
    • R
      rebecca32Aug 20, 2025
      Your Stanley Drill might shut off abruptly because the battery pack has reached its maximum thermal limit, so allow the battery pack to cool down. Also, it could be out of charge. To maximize the life of the battery pack, it is designed to shut off abruptly when the charge is depleted, so place it on the charger and allow it to charge.
  • J
    James CaseyAug 25, 2025
    What to do if Stanley Drill unit will not start?
    • C
      Courtney KimAug 25, 2025
      If your Stanley Drill unit won't start, it could be due to the battery pack not being installed properly, so check the battery pack installation. Alternatively, the battery pack might not be charged, so check the battery pack charging requirements.
  • C
    Cole WalkerAug 29, 2025
    Why will my Stanley SCD20C2 not start?
    • M
      Mark WilliamsAug 29, 2025
      If your Stanley Drill doesn't start, it could be due to a couple of reasons. First, check that the battery pack is installed properly. Second, the battery pack may not be charged, so verify its charging requirements.
  • J
    Joshua OrtizSep 2, 2025
    What to do if Stanley Drill starts immediately upon inserting battery?
    • E
      eleeSep 3, 2025
      If your Stanley Drill starts immediately upon inserting the battery, the switch might have been left in the “on” position. To prevent this, ensure the switch is moved to the “off” position before inserting the battery.

Stanley SCD20C2 Specifications

General IconGeneral
Voltage20V
Max Torque45Nm
Speed Settings2
Battery TypeLithium-Ion
TypeCordless Drill
Chuck Size13mm
Weight1.3 kg
No Load Speed0-1, 500 RPM
Drilling Capacity (Steel)13mm

Related product manuals