ENGLISH
38
38
5.Store tools that are not being used. When not
in use, tools should be stored at a dry and closed
location out of the reach of children.
6.Do not force the tool. The tool operated better
and safer at the assigned characteristic for which
it has been designed.
7.Choose the right tool. Do not force a small tool
to carry out the work that corresponds to a heavy
tool. Do not use tools for purposes for which they
have not been designed; for instance, do not use
circular saws for cutting the trunks of trees or the
branches thereof.
8.Dress suitably. Do not use loose-fitting garment
or jewellery articles that may get caught by
moving parts. The use of nonslip footwear is
recommended for working at outside locations.
For long hair use protective caps.
9.Use safety equipment. Use protective goggles.
Use face protector or mask to avoid dust if the
cutting operations may generate it.
10.Connect the dust-extraction equipment.
Should devices for the connection thereof to dust
extraction and collection equipments be provided,
make sure that they are in fact connected and
adequately used.
11.Do not mistreat the cables. Never pull the
cable to disconnect it from the socket. Keep the
cable away from heat, oil and cutting edges.
12.Secure operations. When possible, use
fastening clasps or clamps for workbenches for
fastening the workpiece. This is safer than using
your hands.
13.Do not excessively extend our radius of
operation. Always keep a firm stand on the
ground and preserve your equilibrium.
14.Service tools carefully. Keep cutting tools
sharpened and clean for a better and safer
operation thereof. Follow the instructions for
greasing and the changing of accessories.
Periodically check extensible cables and replace
them if they are damaged. Keep grips dry, clean
and free of grease and oil.
15.Disconnect the tools. Disconnect tools form
the grid supply when not in use, before repairing
and when changing accessories such as saw
blades, drilling bits and blades.
16.Remove setting keys and adjustable
spanners. Make it your custom to check that
setting keys and adjustable spanners are
removed from the tool before it is operated.
17.Avoid unintentional starting. Make sure that
the switch is in the “open“ position when plugging
the machine into the socket.
18.Use extensible cables for outside use. When
using the tool at an outside location, only use
extensible cables for outside use that are marked
for this purpose.
19. Be alert. Look at what you are doing, use
common sense and do not work with the machine
when you are tired.
20.Check damaged parts. Before using a tool
again, it should be carefully checked so as to
determine that it will operate suitably and be apt
for the operation which has been assigned to it.
Check the alignments and fixings of the movable
parts, breakages of parts, assembly and other
conditions that may affect the operation. A
damaged guard or other part should be suitab ly
repaired or replaced by an authorized technical
service unless anything else is stated in the
instructions manual. Have faulty switches
replaced by an authorized technical service. Do
not use the tool if the switch does not switch on or
switch off.
21.Warning: The use of any accessories or
supplements other than one recommended in this
instructions manual may generate personal
damages.
22.Have the tool repaired by qualified
personnel. This electrical tool complies with the
appropriate safety requirements. Repairs should
be carried out by qualified personnel only using
original spareparts; otherwise, a considerable risk
could be generated for the user.
Measure to be kept by saw blades (EN847):
Diameter of the saw blade: 254 mm
Thickness of the base disk: 1.8 – 2.8 mm
Hole diameter: 30 mm
Information on noise and vibration
The typical noise pressure level of the apparatus as
determined with an A-filter is: see table
Wear ear protection!
The typical vibration transmitted to the hand / arm is
2
lower than 2.5 m/s .
24.Warrantee
23.Technical specifications
Warrantee card
You will find the warrantee card among the
documents belonging to the tool. You must fill in the
warrantee card completely and attach a copy of the
purchase ticket or invoice thereto, and give it to your
distributor against the corresponding
acknowledgement of receipt.
Observation! Should this card be lacking,
immediately request your distributor to furnish it.
Terms of warrantee
As professional equipment, the warrantee period is
set to one year as from the date of purchase.
The warrantee will immediately cease to exist when
the client's service of the central offices does not
have the warrantee card within a one-month term
as of the date of purchase.
The warrantee will equally cease to exist when the
machine has been used in an inappropriate manner
or making use of accessories being unsuitable for
the uses as foreseen by the manufacturer.
To Next Page
Loading...
