Steinbach Poolrunner - Page 8

Poolrunner | 2015_V1
Page 8 of 50
EN
Take off the filter bag, drain and clean it and put on the filter bag
again. Figure 25,26,27
Important
Please press the buckle to remove or restore the filter cartridge. If
this is not observed, it may cause damage to the lower part of the
cleaner.
 Press the buckle simultaneously. Figure 28
 Do not pick up the two parts of the cartridge at the same time. Fi-
gure 29
 The installation must be initiated from one side. Figure 30
 Press the buckle. Figure 31
 Press the buckle on the other side. Figure 32
 Lift out the filter cartridge from one side. Figure 33
 Install the filter cartridge. Figure 34
 Remove the filter cartridge. Figure 35
Remove bzs. Assembly of the filter bag. Figure 36
Tips and advices
 Each time the cleaner is removed from the water, the filter element
has to be cleaned.
 The pH-value of the pool water must be between 7.0 - 7.4.
 The water temperature must be between 10 ° C and 32 ° C.
 After pressing the "power off" button, the “power on” button can’t
be pressed for 30 seconds.
 We recommend to keep the cleaner between 5 ° C and 40 ° C in a
shaded, well-ventilated place. The supply cable must be wound up
for storage. (The float on the cable must not be moved, so that a
perfect swimming of the cable in the water is maintained) Avoid di-
rect exposure to the sun all the time!
 Before using, please read the instruction for fault rectification thor-
oughly.
 Keep the cleaner always on the handgrip to remove it in and out of
the pool.
Trouble Shooting
Symptom
Possible reason
Corrective action
Cable twists or
coils up.
The pool cleaner
turns while cleaning
the water (note, this
is normal).
Unplug power line,
complete the cable
and unscrew.
Obstruction in pool.
Remove obstruction in
pool.
The cable in the wa-
ter is too long.
Get the excess part of
the cable from the wa-
ter. The cable in the
water has to be long
enough to allow the
cleaner to reach all
corners of the bath.
The cleaner does
not reach all pool
area.
Connecting cable is
not long enough.
Allow the cleaner to
reach all corners of the
bathroom, enter the
maximum length of the
connecting cable into
the pool, but consider
a corresponding mini-
mum distance of the
control unit to the pool.
The pool shape
doesn’t make a
complete cleaning
possible.
Slide the pool cleaner
by hand to the places
where was not cleaned
and restart manually
backwards forwards
The water cycle of
the bath is switched
on.
Turn off the filter
pump.
The cleaner does
not work.
Too much air in the
case.
Turn off the machine
and let all the air es-
cape.
A foreign object is
in/at drive.
Contact the service
center.
The cleaner does
not clean optimal.
Cleaner kicking up
dirt and does not
clean enough.
Turn the two water jets
to 180 °. This reduces
the speed and the pu-
rification is improved.
Service processing
Please do not send the unit unauthorized to us, but you should first
contact our service center!
If the product needs to be picked up, so it is necessary to pack it
safely and enclose the invoice (copy) and a copy of the warranty
card.
Once the unit has been returned to us, it will be checked for defects
and repaired of our complaints department. After completing this
work, your device will be returned to you as quickly as possible.
If the submission to guarantee isn’t justified, then the costs incurred
will be charged.
The Warranty/Guarantee runs on the company Steinbach Ver-
triebsgmbH. The item will be repaired by the company Steinbach
VertriebsgmbH, because there exist no right of return, the pool
cleaner will not be taken back.
Steinbach VertriebsgmbH,
Aistingerstrasse 2, 4311 Schwertberg, Österreich
e-mail: service@steinbach.at
www.steinbach.at