What to do if status indicator 4 blinks red on Steinbach Swimming Pool Vacuum?
If the status indicator 4 on your Steinbach Swimming Pool Vacuum is blinking red, it means the device is out of the water. Place the device in the water or switch it off if you are not going to use it at present.
What to do if my Steinbach Swimming Pool Cleaner does not completely move up the wall?
If your Steinbach Swimming Pool Cleaner isn't fully climbing the wall, several factors could be at play. Start by checking the filter and cleaning it if it's clogged. Algae growth on the walls can also hinder movement, so clean the pool walls. Ensure the water temperature is within the operating range specified in the technical data. Inspect the tires and cleaning roller for wear, replacing them if needed. If the device seems too light and topples, switch it off to release trapped air. Also, verify that the pH and chlorine levels are correctly set according to the technical data. Finally, if the device lacks buoyancy, attach additional buoyancy aids included in the package.
Why Steinbach Swimming Pool Vacuum doesn't completely move up the wall?
Several factors can prevent your Steinbach Swimming Pool Vacuum from fully moving up the wall: * The filter may be clogged, so you should clean it. * Algae growth on the walls can be a factor. Manually pre-clean the pool walls. Investigate and remedy the cause of algae growth and use the pool cleaner more frequently. * The water temperature might be too high or low. Operate the device at the recommended water temperature. * Worn tires or cleaning roller. Check and replace them if necessary. * The device might be too light. In this case, switch off the device and let all the air escape. * Incorrect pH or chlorine levels. Adjust them to the correct values.
What to do if Steinbach Swimming Pool Vacuum rises to the surface?
If your Steinbach Swimming Pool Vacuum is rising to the surface, it could be due to the following reasons: * The device climbs too high or there is air trapped inside. To solve this, switch off the device and let all the air escape. * High salt content in the water increases buoyancy. Adjust the salt content to the correct level.
What to do if Steinbach Swimming Pool Vacuum does not sink?
If your Steinbach Swimming Pool Vacuum isn't sinking, here’s what could be happening: * Air trapped inside the device. Turn it off and release all the air. * The salt content in the pool is too high, causing increased buoyancy. Adjust the salt content to the correct level.
What to do if Steinbach Swimming Pool Vacuum cannot reach all places in the pool?
If your Steinbach Swimming Pool Vacuum isn't reaching all areas of the pool, it might be due to: * The pool's filter system is running. Turn off the filter system. * The device is getting stuck on the drain grate. Turn off the filter system.
What to do if my Steinbach Swimming Pool Cleaner rises to the surface?
If your Steinbach Swimming Pool Cleaner is rising to the surface, this could be due to a couple of reasons. First, switch off the device and let all the air escape, as the device may be climbing too high or there may be air trapped inside. Alternatively, the salt content might be too high, increasing buoyancy. In this case, set the correct salt content according to the technical data.
Why Steinbach Swimming Pool Cleaner device cannot reach all spots?
If your Steinbach Swimming Pool Cleaner isn't reaching all areas, it could be due to the pool's filter system being active; switch it off. Also, the device might be getting stuck on the drain grate, in which case, switch off the filter system of the pool.
What to do if my Steinbach Swimming Pool Cleaner does not sink?
If your Steinbach Swimming Pool Cleaner is not sinking, it may be due to air trapped inside; switch off the device and let all the air escape. Alternatively, a high salt content can increase buoyancy; adjust the salt content as per the technical data.
What to do if the status indicator is lit pink on Steinbach Swimming Pool Cleaners?
If the status indicator on your Steinbach Swimming Pool Cleaner is pink, the device is out of the water. Switch the device off. Only switch the device back on once it is in the water and all the air has escaped.
Instructions contain important information about start-up and operation.
Device is designed for private pools and specific liner types.
Essential safety rules for operating the device and handling electrical hazards.
Details the function of the device for cleaning pool floors and walls.
Explains the meaning of the LED indicator lights on the device.
Step-by-step guide for charging the device's battery.
Instructions for correctly inserting the filter unit into the device.
Procedure for taking out the filter unit from the device.
Steps to properly clean the filter unit after use.
Instructions for environmentally friendly disposal of packaging materials.
Guidelines for the proper disposal of the used electrical appliance.
General| Type | Robotic |
|---|---|
| Power Source | Battery |
| Operating Time | 90 minutes |
| Warranty | 2 years |
| Pool Type | Inground Pool |
| Cleaning Area | Pool Floor, Pool Wall |
| Cleaning Technology | Brush |
| Battery Life | 90 minutes per charge |
| Charging Time | 5-6 hours |
To Next Page
