To Next Page
M
Molly JohnsonAug 30, 2025
Why doesn't the bike handle clamp on my Stihl FS 410 Brush Cutter?
- VVanessa KellyAug 30, 2025
If the bike handle does not clamp, the clamps may be greasy or oily. Clean the clamps and bike handle.
Why doesn't the bike handle clamp on my Stihl FS 410 Brush Cutter?
If the bike handle does not clamp, the clamps may be greasy or oily. Clean the clamps and bike handle.
Why is my Stihl FS 410 drive tube assembly vibrating?
If the drive tube assembly vibrates, the flexible liner may be worn, causing the drive shaft to be insufficiently supported. Replace the flexible liner.
Why does the drive tube assembly on my Stihl FS 410 get very warm?
If the drive tube assembly becomes very warm, the drive shaft may not be sufficiently lubricated. Lubricate the drive shaft along its entire length, ensuring the entire length of the flexible liner is lubricated.
What to do if starter rope can be pulled out almost without resistance on Stihl FS 410 Brush Cutter?
Replace pawls.
What to do if irregular spark on Stihl FS 410 Brush Cutter?
Check proper functioning of lever for stop function/contact spring or slide control/microswitch and ignition module. If there is damaged insulation or interruption in the ignition lead or a short circuit wire, check the ignition lead/ignition module, and replace the ignition module if necessary. Check operation of spark plug, clean spark plug and replace if necessary. For versions with M-Tronic, carry out diagnosis.
What to do if metering diaphragm damaged or shrunk on Stihl FS 410 Brush Cutter?
Replace metering diaphragm.
Why is the starter rope hard to pull on my Stihl FS 410 Brush Cutter?
If the starter rope is difficult to pull or rewinds very slowly, the starter mechanism may be very dirty. Thoroughly clean the complete starter mechanism.
Why does my Stihl FS 410 Brush Cutter carburetor flood and the engine stall?
If the carburetor floods and the engine stalls, the inlet needle may not be sealing due to foreign matter in the valve seat or cone. Remove and clean the inlet needle or clean the carburetor.
Why does the cutting attachment on my Stihl Brush Cutter stop under load?
If the cutting attachment stops under load at full throttle, it could be because the clutch shoes or clutch drum are badly worn. Install a new clutch or clutch drum.
Why won't the starter rope rewind on my Stihl FS 410 Brush Cutter?
If the starter rope does not rewind, heavy fouling or rust may be present on the rewind spring. Clean or replace the rewind spring.
General| Fuel Tank Capacity | 0.75 L |
|---|---|
| Shaft Type | Straight |
| Engine Power | 2.0 kW |
| Displacement | 41.6 cc |
| Overall Length | 180 cm |
Guidance on using the manual, including applicable documents and symbol meanings.
Identification and description of the main parts of the STIHL brushcutter.
Illustrations and descriptions of various deflectors and cutting attachments.
Understanding warning signs, symbols on the trimmer, and their meanings for safety.
Specifies the intended applications and necessary qualifications for the operator.
Guidelines for operator health, supervision, and essential personal protective equipment (PPE).
Ensuring a safe working environment free from bystanders and hazards.
Criteria to ensure the brushcutter is in a safe, operational condition.
Ensuring components like deflectors, mowing heads, and cutting attachments are safe and correctly installed.
Guidelines for safe fuel handling, refueling, and general operation safety.
Understanding kickback and reactive forces for safe operation.
Steps for preparing the brushcutter, and guidelines for transport and storage.
Procedures for cleaning, routine maintenance, and repairs.
Instructions for mounting the bike handle, deflector, and limit stop.
How to attach and detach the skirt for the deflector.
Instructions for mounting mowing heads and metal cutting attachments like blades and knives.
Procedures for attaching shredder blades and circular saw blades.
Instructions for safely removing metal cutting attachments.
Steps to adjust the harness, bike handle, and balance the brushcutter for user comfort.
Instructions for preparing the correct fuel mixture and refueling the brushcutter.
Detailed steps for safely starting the brushcutter engine.
Procedure for stopping the engine and verifying control functionality.
Adjusting the carburetor for winter operating conditions.
Adjusting for summer conditions and proper grip for control.
Methods for mowing, thinning, and sawing with different attachments.
Steps after work: cleaning, safe transport, and storage guidelines.
Instructions for cleaning the trimmer, deflector, and cutting attachment.
Scheduled maintenance tasks including lubrication and part replacement.
Guidance on sharpening, balancing, and general repair information.
Common problems, solutions, and air filter replacement procedure.
Procedures for spark plug maintenance and idle speed adjustment.
Technical details for FS 410/460 models, including sound and vibration values.
Information on REACH, emissions, and approved cutting attachment combinations.
Details on spare parts, disposal, and the EC Declaration of Conformity.
Official declaration of conformity with UK regulations for the brushcutter models.
