To Next PageTo Next PageWhat to do if Stihl Blower roller brush is blocked?
If your Stihl Blower cuts out because the thermal overload cutout has tripped due to a blocked side broom or roller brush, remove the blockage and wait about 30 seconds for the overload cutout to cool down. If the roller brush is blocked, press the switch to reset the overload cutout.
Why won't my Stihl Blower start, and one LED flashes green?
If your Stihl Blower doesn't start, and one LED on the battery flashes green, the battery charge is low. You should charge the battery.
Why is one LED on my Stihl Blower battery red?
If your Stihl Blower doesn't start, and one LED on the battery glows red, the battery might be too hot or too cold. Allow the battery to cool down or warm up slowly to a temperature of about +15 °C - +20 °C.
How to check battery contacts on Stihl Blower?
If your Stihl Blower doesn't start, it might be due to poor electrical contact between the power tool and battery. Remove the battery, visually inspect the contacts, and then reinsert the battery.
What to do if 3 LEDs on my Stihl Blower battery flash red?
If your Stihl Blower doesn't start and 3 LEDs on the battery flash red, remove and refit the battery. If the LEDs continue to flash, the power tool has a malfunction and should be checked by a servicing dealer.
What to do if 3 LEDs on my Stihl Blower battery glow red?
If your Stihl Blower doesn't start and 3 LEDs on the battery glow red, the power tool is too hot. Allow it to cool down.
Why does my Stihl Blower keep cutting out?
If your Stihl Blower cuts out, the battery or electronics might be too hot. Remove the battery and allow both the battery and the blower to cool down.
What to do if LED on Stihl Blower charger flashes red?
If the LED on the charger flashes red, it could indicate: * No electrical contact between the charger and battery. Remove the battery and refit it. * A fault in the battery (4 LEDs on the battery flash red for about 5 seconds). Take the battery out of the power tool and refit it. Switch on the machine – if the LEDs continue to flash, the battery has a malfunction and must be replaced.
What to do if Stihl Blower battery jams when being inserted?
If the battery jams when being inserted into the power tool or charger, the guides or contacts may be dirty. Carefully clean the guides and contacts.
What to do if Stihl Blower battery is not being charged even though LED on charger glows green?
If the LED on the charger glows green but the battery isn't charging, the battery may be too hot or too cold (1 LED on the battery glows red). Allow the battery to cool down or warm up slowly at a temperature of about +15°C to +20°C. Only operate the charger in closed, dry rooms at ambient temperatures between +5°C and +40°C.
General| Power Source | Battery |
|---|---|
| Battery Technology | Lithium-Ion |
| Sweeping Width with Side Broom | 770 mm |
| Container Capacity | 50 l |
| Vibration Level | 2.5 m/s² |
Explains pictograms attached to the machine and shown in this manual.
Explains warning and notice symbols used within the text for safety and caution.
Explains STIHL's philosophy on product improvements and potential updates not in the manual.
Details intended use, health hazards, and general safe operating practices for the cordless sweeper.
Covers local safety regulations, user experience, supervision, and child safety during operation.
Instructions on how to properly dispose of the battery and charger.
Checks and preparations required before operating the power tool.
Safe practices and considerations while operating the power tool.
Procedures to follow after completing work, including cleaning and battery removal.
How to properly hold and maneuver the power tool during operation.
Instructions on how to safely carry the machine.
Guidelines for securing the machine when transporting it in a vehicle.
Steps to remove the push handle from the machine.
Steps to install the push handle onto the machine.
Explains communication between power tool, battery, and charger for proper function.
Indicates issues like no electrical contact, battery malfunction, or charger malfunction.
Indicates the battery is being charged or is too hot/cold for charging.
Steps for inserting and securing the battery into the power tool.
How to turn the power tool on using the on/off switch.
How to adjust the height of the side brooms for optimal cleaning.
Explains the function of the guide roller for edge control.
How to use the hold-down device to keep bristles close to the ground.
Explains the function of the thermal overload cutout for motor protection.
Instructions for removing and emptying the hopper after use.
Steps to remove the battery from the power tool.
Method to straighten bent or twisted bristles using a hairdryer.
Instructions for lubricating the gearbox with STIHL silicon spray.
Steps to remove, clean, and refit the air filters.
Emphasizes regular maintenance and recommends authorized dealers for complex tasks.
Lists components like side brooms, roller brush, and battery that are subject to normal wear.
Details model, type, and operational constraints for the battery.
Lists specifications for AL 100 and AL 300 chargers, including voltage, current, and insulation.
Provides charging times for different battery models with AL 100 and AL 300 chargers.
Lists dimensions for the push handle in upright and working positions.
Reports sound power level and vibration measurements according to relevant directives.
Lists optional accessories such as STIHL battery, charger, and cover.
