The KARL STORZ SMARTSCREEN (Item number: WM200) is a medical device designed for use by qualified personnel in practices and operating rooms. Its primary function is to control allocated, compatible KARL STORZ medical devices, such as the KARL STORZ AIDA® WD300, from within an unsterile area. The device should be positioned under compatible KARL STORZ equipment.
Function Description
The SMARTSCREEN facilitates the display of video signals from various signal sources and destinations during medical procedures. It also provides control inputs for managing connected devices. This combination allows a non-sterile user to view and preoperatively interact with connected medical devices within the medical area. Data and images are presented on a FULL HD display, and the device supports 10-finger multi-touch functionality for processing information.
Important Technical Specifications
Display:
- Colors: 16.7 million colors (8 bits)
- Response time (Tr + Tf): 25-35 ms
- Life span: At least 12,000 operating hours
- Panel: AHVA
- Backlight type: LED
- Visible diagonal: 21.5"
- Brightness: 300 cd/m²
- Native resolution: 1,920 x 1,080 pixels
- Pixel pitch: 0.144 x 0.144 mm
- Viewing angle: Horizontal 170° / vertical 170°
- Contrast ratio, nominal: 700:1
Power supply:
- Average energy consumption: < 6 W
- Maximum energy consumption: < 8 W
- Input voltage (DC): 12 V
Inputs:
- Video input: DisplayPort 1.2
- Power connection: 8-pin connection
- Touch signal input: USB-B 2.0
- Other: Potential equalization connection (POAG)
Touchscreen:
- Technology: PCAP
- Driver: No installation required in Windows
- Support: Windows, Linux kernel 3.x.x and 4.x.x
- Number of points of contact: Max. 10
General:
- Dimensions (L x W x H): 305 x 355 x 46 mm
- Weight: 6.6 kg
Ambient Conditions:
- Storage/transport conditions:
- Ambient temperature: -20°C ... +60°C
- Relative humidity: Max. 90%
- Operating conditions:
- Ambient temperature: 0°C ... 50°C
- Relative humidity: Max. 80%
Usage Features
The SMARTSCREEN is designed for intuitive operation with its 10-finger multi-touchscreen. It integrates seamlessly with compatible KARL STORZ medical devices, allowing for remote control and display of critical information. The device's robust design and compliance with IEC standards ensure safe operation in professional healthcare environments.
Connectivity:
- Potential equalization connection: For safety and proper grounding.
- DisplayPort video output sockets: For video signal transmission.
- USB-B port: For touch signal input and communication with connected devices.
- 12 V direct current input socket: For power supply.
Setup and Operation:
- Unpacking: Carefully remove the product and accessories from the packaging. Inspect for damage and document any shipping damage.
- Inspection: Before use, check all components for visible contamination, hidden defects, and overall completeness. The product is delivered unsterile and must be reprocessed according to instructions before initial and subsequent use.
- Setting up: Place the product on a horizontal, flat surface. Ensure the power cord can be unplugged at any time and that there is adequate air circulation.
- Connecting:
- Connect the DisplayPort cable to the video output socket of the SMARTSCREEN and to the AIDA (WD300) video output socket.
- Connect the USB cable to the USB-B port of the SMARTSCREEN and to the AIDA (WD300) USB-A port.
- Connect the AIDA (WD300) serial interface to the direct current input socket using an RS232 to DC connector.
- Putting into operation:
- Gently press the front panel of the monitor and turn the screw lock at the rear counterclockwise.
- Press the monitor front panel to release the monitor guide.
- Pull out the monitor and move it into the desired position.
- Image signals not originating from a KARL STORZ device should only be used for information purposes.
Maintenance Features
Regular maintenance is crucial for the longevity and proper functioning of the SMARTSCREEN.
- Maintaining the product: Maintenance activities should only be performed by KARL STORZ or a KARL STORZ authorized company.
- Maintenance interval: An annual safety test is recommended.
- Repairing the product: Repair work must be performed by KARL STORZ or a KARL STORZ authorized company. Always contact your local KARL STORZ subsidiary or authorized dealer for repair services. Contaminated products must be decontaminated before shipment for repair.
- Disposing of the product: The product meets the requirements of the Directive on Waste Electrical and Electronic Equipment (WEEE). Disposal must comply with applicable national laws and regulations. The product must be disposed of at a suitable collection point for the reprocessing of electrical and electronic equipment. Contact KARL STORZ SE & Co. KG or an authorized dealer for information on collection points.
- General: Read and follow all safety notes and warnings in the instructions for use. Keep the instructions visible near the product.
- Serious incidents: Any incident leading to death, serious deterioration in medical condition, or a serious threat to public health must be reported to the manufacturer and appropriate authority.
- Damaged products: Do not use damaged products; inspect all components before each use.
- Unsterile product: The product is not sterile upon delivery. Reprocess according to instructions before initial and subsequent use to prevent infection risks.
- Contaminated products: Comply with national laws and regulations and observe guidelines of the Employer's Liability Insurance Association to prevent infection risks.
- Electric current: Improper power supply can cause electric shock. All electrical installations must meet IEC standards. Installation and servicing must be done by authorized electricians. Use only KARL STORZ supplied power cords or equivalent. Operate only with the stated line voltage. Ensure the power cord is accessible for disconnection. Ensure potential equalization. Connect to a properly installed, approved socket. Do not open the product. Do not service the product yourself. Do not touch output jacks or the patient simultaneously. Unplug the mains plug before maintenance.
- Liquid ingress: Ingress of liquid can damage electrical components. Do not store liquids near the product. If liquid enters, unplug and dry the product.
- Electromagnetic interference (EMI): The device is a medical electrical device and requires special precautions regarding EMC. It must be installed and commissioned according to EMC information. Portable RF communications equipment should be kept at least 30 cm from the product. Observe the information on electromagnetic compatibility in the manual. Use only accessories and cables recommended by the manufacturer. The product should not be used immediately adjacent to or stacked with other equipment unless normal operation is verified.
- Combination with other components: Only combine with devices and components approved by the manufacturer. All connected devices must comply with relevant IEC or ISO standards. All configurations must comply with IEC 60601-1. Do not make unauthorized changes to the product.
Need help?
General
To Next Page