Strong Super Trouper - Bulb Installation

BULB INSTALLATION

CAUTION:OBSERVEALLSAFETYPROCEDURES.Putontheprotectiveface
mask.Wearcleancottonglovestopreventmarkingthequartzenvelopeofthebulbwithngerprints.
 REMOVE THETOP COVER of the lamphouse by removing the four Holt head
(tamperproof)screwswiththespecialscrewdriverprovided.
 NOBULBADAPTERSarerequiredtoinstallthe2000wattbulbintheXenonSuper
Trouperlamphouse.Componentsandadaptersrequiredtoinstallthe1000wattor1600wattbulb
inthelamphouseareavailableinanoptionalAdapterKit(PartNo. 7201192) .SeetheBulbAdapter
illustrationonthefacingpageforthecorrectadaptersandmethodofassembly.



DISMOUNTANDREMOVEthefrontbulbmountingringassemblyfromtheairduct
castinginfrontofthereectorandreplaceitwiththesmallerbulbsupportyokecastingincludedin
the7201192BulbAdapterKit.Installthe65148000cathodeclampinplaceofthestandard2kW
clamp.Removetherearbulbsupportcolletassembly(nylonrodandbrasssocket)fromthebulbfocus
assemblybehindthereectorandreplaceitwiththecolletassemblyincludedintheBulbAdapterKit.

 ASSEMBLETHEREQUIREDADAPTERStothe1000or1600wattbulbpriorto
insertingthebulbintothelamphouse.Beverycarefulnottoapplyanystrainonthequartzenvelope
wheninstallingadapters. Handlethebulbbyitsmetalendcapsonly.Screwthethreadedcathode
adapterontothenegativestudsoitseatsrmlyagainsttheshoulderofthecathode(-)endcap.
Applytorqueusingthepinsonthecathodeendcap.Sliptheanodeadapterwithsetscrewoverthe
positivestud,uptotheshoulderoftheanode(+)endcap.Tightenallfastenerssecurelytoinsure
agoodelectricalconnection. 
 REMOVETHEPLASTICPROTECTIVECOVERfromthexenonbulbonlyifnec-
essary.Insertthebulbthroughthetopofthelamphouse,betweenthereectorsupportandthefront
casting.Passtheanode(+)endofthebulbthroughtheholeinthereector,takingcarenottotouch
thesurfaceofthereector.
 INSERTTHEANODEADAPTERSTEMof1000and1600wattbulbsintotherear
supportcollet.Thestemmustbeinsertedintothesocketasfaraspossibletopermitfullfocustravel
ofthebulb.Placethestemofthecathodeadapterintofrontbulbsupportyoke,pivottheretaining
platetoitsclosedposition,andtightenthe(2)thumbscrews.Tightenthesocketheadclampingscrew
intheanodecontactsecurelytoinsureagoodelectricalcontact.
 INSTALLTHECATHODELEADCONTACTovertheendofthecathodeadapter
uptotheshoulderofthecontactandtightentheclampingscrewsecurely.Dresstheleadinfrontof
theairducttominimizetheshadow.
XST/009
1000&1600WattBulbInstallation