Stryker MMP200 - Page 2

149 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Table of Contents

Default Chapter5
- Table of Contents5
1 Warnings and Cautions10
- Safeguards and Precautions10
- Warnings10
2 Product Symbol Definition11
3 Tool List13
- Required Tools13
- Optional Tools13
4 Unpacking14
- Halogen Light14
- LED Light15
- Flat Panel Arms17
- Booms17
5 Preparing the Mounting (Interface) Plate18
6 Preparing the Suspensions19
- Installing the Cable Kit for Lights19
- Surgical Lights20
- Flat Panel22
- Booms22
- Routing Cables24
7 Installing the Suspension and Boom Arms25
- Alternate Light Installation Instructions (Continued)26
8 Installing Light Heads27
- LED and Halogen27
  - Standard Light27
  - Low Ceiling Light28
9 Powering the System31
- Halogen Lights31
  - Electrical and Data Connections31
- LED Lights32
  - Power Supply Box Wall Mount (Optional)32
- Power Supply Box Connections33
- Visum LED New Installation Setup36
10 Monitor Assembly40
- Light Flat Panel or Single Panel Installation40
- Adjusting the Yoke41
  - Adjusting the Width41
  - Adjusting the Height45
- Attaching the Monitor46
- Balancing the Monitor48
- Adjusting the Brakes50
11 Boom Shelf Attachment and Adjusting Brakes/Stops51
- Boom Shelf and Accessories Attachment51
- Lights and Flat Panel Arms60
- Adjusting the Cardanic Suspension66
- Boom Arms67
  - Osc40067
  - Osc60070
12 Installing Covers72
- Lights and Flat Panel Suspension72
- Booms72
- Tandem73
- Cable Covers75
- Installing a Flexstrip Kit (Dual Flat Panel Arm Only)78
13 Accessories79
- Lights79
14 Legacy84
- Suspension Installation84
- Installing Spring Arms (if Necessary for Lights Only Suspension)84
- Standard Width Yoke87
- Halogen Light Flat Panel Stop Replacement87
- Variant89
- Installing GCX Accessory Track on OSC400 Service Head89
15 Cleaning and Completion93
16 Servicing the Visum 600/45094
- Electronic Control System94
- Power Supply Box96
  - Halogen Power Supply Box Troubleshooting Guide96
- Wall Control99
- Plug Layout of the Electronic Control System101
- Plug Allocation101
- Can Bus Troubleshooting110
  - Light Block Diagram110
17 Servicing Booms114
- System Operation114
- Troubleshooting114
  - Air Leaks115
- Miscellaneous Hardware Parts List117
- Replacing the Trim Strip119
- Replacing Med Gas120
  - Replacing a Nitrogen Regulator120
  - Replacing Med Gas Plate120
- Replacing the Brake Bladder121
- Reassembling the Service Head127
- Replacing the Motor133
- Electro-Pneumatic (EP) Module135
  - Removing the Electro-Pneumatic (EP) Module135
  - Installing an Electro-Pneumatic (EP) Module135
- Generation 1 Service Head136
  - Replacing a Shelf with Brake136
  - Replacing the Brake Button138
18 Servicing the LED140
19 Replacement Part Numbers141
20 Contact Information147

Related product manuals

Preview: Stryker M-1

Preview: Stryker MV3 5900

Stryker MV3 5900

Preview: Stryker M Series

Stryker M Series

Preview: Stryker MX-PRO R3

Stryker MX-PRO R3

Preview: Stryker S3 MedSurg 3002

Stryker S3 MedSurg 3002

Preview: Stryker MedSurg Standard 3002 S3

Stryker MedSurg Standard 3002 S3

Preview: Stryker SDC3

Preview: Stryker X8000

Preview: Stryker Power-PRO XT

Stryker Power-PRO XT

Preview: Stryker ProCuity Series

Stryker ProCuity Series

Preview: InterPulse 0210 000 Series

InterPulse 0210 000 Series