18
Owner's Manual
17
Owner's Manual
1. Press SETUP on the infrared hand unit.
2. Select CH
Channel Setup.
3. Press VOL
to accept this selection.
4. Press CH
to select a Channel Setup option.
Antenna : CATV/TV - Select CH
Antenna: to change the source of the TV signal.
Choose VOL CATV (cable TV), when
cable is the signal source. When an antenna
is the signal source, choose TV. In almost all
hospitals, cable is the source of the signal.
CATV Install
The chart below is typical of many cable channel allocations.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to article 820-40 of the NEC
that provides guidelines for proper grounding and, in particular, specifies that cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as practical.
Assign channel maps -
A channel map is the method of organizing channels
in different service levels. When a map does not contain any channels, the word
"empty" appears beside it. Before you identify which channel map should go with
which service level, you must know which channels, the map contains. It is
easiest to keep a written list of the map number and the channels assigned to it.
To identify which channels are included in a channel map ...
Select CH ADD/Delete channels.
Press VOL to accept the selection.
Select CH the desired map.
Press VOL to accept the selection. Add/Delete channels for the selected Map #.
Press CH to change channels. When + appears before the channel
number, this channel is included in the selected Map. When - appears before
the channel number, this channel is not
included.
How do I change the set up of the channels?
A-8 A-4
01
28
47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
96 97 98 99 14 15 16 17 18 19 20 21 22 23 24 25
26
27
A-3 A-2 A-1 A B C
OPQRS T UVW
W 1W2
W 11 W 12 W 13 W 14 W 15 W 16 W 17 W 18 W 19 W 20 W 21 W 22 W 23 W 24 W 25 W 26 W 27 W 28 W 29
W
30 W 31 W 32 W 33 W 34 W 35 W 36 W 37 W 38 W 39 W 40 W 41 W 42 W 43 W 44 W 45 W 46 W 47 W 48
85 86 87 88 89 90 91 92 93 94 100 101 102 103 104 105 106 107 108
W 49 W 50 W 51 W 52 W 53 W 54 W 55 W 56 W 57 W 58 W 59 W 60 W 61 W 62 W 63 W 64 W 65 W 66 W 67
109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125
W 68 W 69 W 70 W 71 W 72 W 73 W 74 W 75 W 76 W 77 W 78 W 79 W 80 W 81 W 82 W 83 W 84
W 3W4W 5W6W 7W8W9
W 10
DE FGHI JKLM N
A-5
95
SETUP MENU
Rental: Free
Picture
Sound
Channel Setup
Features
Blocking
Language: English
TO Select
+
-
To Accept
Main SETUP MENU
Bass - Select CH Bass to adjust the amount of bass in the sound.
Hold down VOL+ to increase or the VOL- button to reduce bass.
Treble - Select CH Treble to adjust the amount of treble in the sound.
Hold down VOL+ to increase or the VOL- to reduce treble.
Balance - Select CH Balance to adjust the balance in the sound.
Hold down VOL+ to increase right volume, and hold down VOL- to increase left
volume.
Mts - Select CH Mts to adjust the mts of the sound.
Hold down VOL+, the selection will change in the order Stereo - Sap - Mono.
How do I adjust the quality of the TV sound?
NOTES:
Reception of Sereo or SAP broadcast information is of course dependent on a
television station actually broadcasting such material. Not all stations do, and
some stations only broadcast Stereo/SAP material during part of the day.
If the L-10 ELF is set to STEREO and no stereo signal is being broadcast, a
MONO signal will automatically be received.
To Next Page
Loading...