Sunlover oasis IX9 - User Manual

Questions and Answers

J
justincollinsAug 18, 2025
What to do if my Sunlover oasis IX9 shows a high pressure protocol protection error?
- M
  Marcus McclainAug 18, 2025
  If your Sunlover Heat Pump shows a high-pressure protocol error, first ensure adequate water flow by cleaning the pool filter and pump basket, then restart the heater. Also, verify the bypass valve setting. If the issue persists, a technician should inspect the refrigerant system and pressure switch, as it could indicate a refrigerant system fault or failed high-pressure switch.
R
Raymond SantosAug 21, 2025
What to do if my Sunlover oasis IX9 Heat Pump shows a flow switch protocol (no water flow) error?
- D
  dgarciaAug 21, 2025
  If your Sunlover Heat Pump displays a flow switch protocol error indicating no water flow, check the pool plumbing and ensure the filter pump is running. This issue arises when there is little to no water flowing through the heat pump.
E
Eric WatsonAug 23, 2025
What causes a Low Pressure Protocol error in a Sunlover Heat Pump?
- A
  Amy MillerAug 23, 2025
  If your Sunlover Heat Pump is showing a low-pressure protocol error, it could be due to a failed low-pressure switch or a loss of refrigerant. A technician is required to check the pressure refrigerant system and pressure switch.
L
Lance MorganAug 26, 2025
What does Exhaust Air Over Temperature Protocol mean for Sunlover Heat Pump?
- M
  Mark GarrettAug 26, 2025
  If your Sunlover Heat Pump displays an exhaust air over temperature protocol, it indicates the compressor might be overloaded. Verify if the compressor system is operating normally to resolve this issue.
B
Betty MurphyAug 27, 2025
How to fix Pressure Sensor Fault in Sunlover Heat Pump?
- J
  Joshua LopezAug 27, 2025
  If your Sunlover Heat Pump indicates a pressure sensor fault, it suggests the pressure sensor has failed. To resolve this, check or replace the pressure sensor.
B
Brandon ParkAug 30, 2025
What causes Inlet Temperature Sensor Fault in Sunlover oasis IX9 Heat Pump?
- A
  Andrew OliverAug 30, 2025
  If your Sunlover Heat Pump displays an inlet temperature sensor fault, it means the temperature sensor is either open or short circuit. You should check or replace the temperature sensor.
G
Gary MurphySep 1, 2025
How to troubleshoot Outlet Temperature Sensor Fault in Sunlover Heat Pump?
- D
  Donald ClarkeSep 1, 2025
  If you encounter an outlet temperature sensor fault on your Sunlover Heat Pump, the temperature sensor is likely open or short circuit. Check or replace the temperature sensor to fix this.
K
Kelly SmithSep 3, 2025
What does Discharge Temperature Sensor Fault mean for Sunlover oasis IX9?
- C
  cindynguyenSep 3, 2025
  If your Sunlover Heat Pump is showing a discharge temperature sensor fault, it indicates the temperature sensor is open or short circuit. The suggested solution is to check or replace the temperature sensor.
A
Alec TorresSep 6, 2025
What to do if my Sunlover oasis IX9 Heat Pump displays Suction Temperature Sensor Fault?
- H
  Howard MorrisonSep 6, 2025
  If your Sunlover Heat Pump shows a suction temperature sensor fault, this indicates that the temperature sensor is open or short circuit. To resolve this, check or replace the temperature sensor.
K
Kathryn AyalaSep 8, 2025
Why does my Sunlover Heat Pump show Ambient Temperature Sensor Fault?
- Y
  yolandawilsonSep 8, 2025
  If your Sunlover Heat Pump displays an ambient temperature sensor fault, the cause is likely that the temperature sensor is open or short circuit. You should check or replace the temperature sensor.