SunStar SPS/A-Pattern Series - Page 170

170
0/1
0/1
0~3
Upper feed plate control
Back/forth jump stitches
Setting-up reference point for
zooming
Palette signal check
074
075
076
077
NO. Function name Contents Explanation and factory-installed setting value Unit
1) DISABLE
2) ENABLE
1
1) MACHINE_ORG
2) SECOND_ORG
3) SEWING_STRT
4) REFER_PNT
1) DISABLE
2) ENABLE
1) DISABLE
2) ENABLE
Sewing will be allowed whether the upper
feed plate is opened or closed.
Sewing will not be allowed when the upper
feed plate is opened.
User can define stitch value to move.
1~100 [Stitch]
Zooming based on the machine origin.
Zooming based on the second origin set by user.
Zooming based on sewing starting point.
Zooming based on the reference point defined by user at any location.
1
Sewing limit set-up
078
Not used (at the factory)
Used
Do not use signal on the upper feed plate sensor.
Use signal on the upper feed plate sensor.
13(mm)
(For 1306)
X-axis forward direction sewing limit
set-up
079
Sets the size of X-axis forward direction as desired
(1mm~250mm)
1
-13(mm)
(For 1306)
X-axis reverse direction sewing limit
set-up
080
Sets the size of X-axis backward direction as
desired (-1mm~-250mm)
1
6(mm)
(For 1306)
Y-axis forward direction sewing limit
set-up
081
Sets the size of Y-axis forward direction as desired
(1mm~250mm)
1
0~2
1
1
-6(mm)
(For 1306)
1) DISABLE
2) ENABLE
Y-axis reverse direction sewing limit
set-up
Quick origin search motion for 1811
082
083
Sets the size of Y-axis backward direction as desired
(-1mm~-250mm)
Quick origin search motion not used
Quick origin search motion used
Upper-lower shaft origin search motion after
finishing sewing Setting [SPS/C-Series]
084
1) JOB_SETUP
2) JOB_READY
Do not use upper-lower shaft origin search motion after finishing sewing
Do use upper-lower shaft origin search motion after finishing sewing
Machine Head Up-Down Setting
Function [SPS/C-series]
Reverse rotation setting after
trimming
Reverse Rotation Angle after Trimming
Setting Function
Oil control
[SPS/C-Series]
Designate the place of saving pattern
designs
085
086
087
088
090
1) HEAD_DOWN
2) HEAD_UP
3) JUMP_HEADUP
1) DISABLE
2) ENABLE
3) END_SEW
15
4[ms]
1) SAVE USB
2) SAVE FLASH
Do not use the ascending of machine head after finishing sewing.
Do use the ascending of machine head after finishing sewing.
Use the head lift function when it is in the jump motion.
1) Disabled
2) Enabled
3) To be activated after the last trimming is performed
Reverse Rotation Angle after Trimming Setting
(1~40 )
Set the hook lubrication time after trimming
(0~10)
Save in USB (Default value)
Save in Flash Memory
1[sec]
Oil spray off-time cycle setting
089
5
This function sets the oil spray off-time cycle.
(00~50[sec])
091
Deleting Flash Memory Designs When
New Designs Are Opened
1) SAVE
2) DELETE
Enabled (default)
Disabled
092
Setting the Safety Mode
1) DISABLE
2) ENABLE
Not used (at the factory)
Used
093
Jump Speed Setting
1) SLOW_SPEED
2) MIDDLE_SPEED
3) FAST_SPEED
Lowest Jump Speed
Medium Jump Speed
Highest Jump Speed
Design Auto Call Setting
094
1) DISABLE
2) ENABLE
2) ENABLE
This sets the design auto call function.
Sewing Ready Function Setting Upon
Design Auto Call
095
1) DISABLE
This sets whether the machine becomes ready for
sewing, when designs are automatically called.
External Control Signal Use Setting
096
1) DISABLE
2) ENABLE
This sets whether the external input signals are
used to activate Sewing Start, Emergency Switch,
Clamp, and Enter key.
Design Call Sensing Time Setting
097
10
This sets the sensing time for the design auto call
sensors (SEN_0~SEN_3).
1
[100ms]